General Information; Safety Standards; Installation Rules - Nice HDF-45-95 Instructions Et Indications D'installation Et D'utilisation

ENGLISH

GENERAL INFORMATION

The gearmotors to which this instruction booklet refers
are designed for operating fast doors totally balanced with
springs or weights. If these products are to be used for
different applications, it is recommended to first discuss
them with the Manufacturer.
The declaration loses its validity if the gearmotor is modified
(e.g. wiring reversal).

SAFETY STANDARDS

• IMPORTANT! – This manual contains important instructions
and warnings regarding safety. Incorrect installation may cause
serious injury. Before commencing work, all sections of the manual
must be read carefully. If in any doubt, suspend installation and call
the Nice Support Service for clarification.
• IMPORTANT! – This manual contains important instruc-
tions. Keep it for future maintenance work and disposal of
the product.
• IMPORTANT! – Under the latest European legislation, auto-
matic door and gate installations must be compliant with
the standards specified in Directive 2006/42/EC (formerly
98/37/EC) (the Machinery Directive) and the standards EN
12445, EN 12453, EN 12635 and EN 13241-1 in particular,
which enable conformity of the automated functionality
to be de clared. In the light of the above, all work involving
installation, connection, testing and maintenance of the
product must be carried out exclusively by qualified and
competent technicians!

INSTALLATION RULES

• Before commencing the installation, check if the product is suit­
able for the de sired type of use. If it is not suitable, DO NOT con­
tinue with the installation.
• The contents of this manual refer to a standard system.
• All installation and maintenance work must be carried out
with the au to mation system disconnected from the elec-
tricity supply. If the power discon nection device cannot be seen
from where the automation system is po sitioned, then before
starting work a notice must be attached to the disconnection
device bearing the words "CAUTION! MAINTENANCE IN PRO­
GRESS".
• The Control unit must be connected to an electricity supply line
equipped with protective earthing.
• Handle the product with care during installation, taking care to
avoid crushing, denting or dropping it, or contact with liquids of
any kind. Keep the product away from sources of heat and naked
flames. Failure to observe the above can damage the product, and
increase the risk of danger or malfunction. Should this occur, sus­
pend installation work immediately and contact the Nice Support
Service.
• The electrical power line must be fitted with a device that ena­
bles complete disconnection of the automation from the mains.
The disconnection device must have a gap between contacts
that ensures complete disconnection in the conditions of over­
voltage category III, in compliance with installation regulations.
• Do not modify any part of the product. Prohibited modifications
can only lead to malfunctions. The manufacturer declines all
responsibility for damage re sulting from unauthorized changes
made to the product.
• If the gate or door being automated has a pedestrian gate, then
the system must include a control device that will inhibit the opera­
tion of the motor when the pedestrian gate is open.
• The product's packaging material must be disposed of in full com­
pliance with local regulations.
Warnings for use
• The product is not intended for use by persons, including children,
with limited physical, sensory or mental capacities, or who lack
experience or knowledge, unless supervised or trained in the use
of the product by a person responsible for their safety.
• Any children near the automation system must be kept under
supervision to ensure that they do not play with it.
• Do not allow children to play with the fixed control devices. Keep
remote control devices out of the reach of children.
The instructions shall contain at least the following information:
• the business name and full address of the manufacturer and,
where applicable, hisauthorized representative;
• model or type reference of the appliance as marked on the appli­
ance itself, except for the serial number;
• the designation of the appliance together with its explanation in
case it is given by acombination of letters and/or numbers.
• the general description of the appliance, when needed due to the
complexity of the appliance;
• specific precautions if required during installation, operation,
adjusting, user maintenance, cleaning, repairing or moving;
• when needed drawings, diagrams, descriptions and explanations
necessary for the safe use and user maintenance of the appliance;
• the possible reasonably foreseeable misuse and, whenever rel­
evant, a warning againstthe effects it may have on the safe use of
the appliance.
The words "Original instructions" shall appear on the language
version(s) verified by the manufacturer or by the authorized repre­
sentative.
When a translation of the original instructions has been provided by
a person introducing the appliance on the market; the meaning of
the sentence "Translation of the original instructions" has to appear
in the relevant instructions delivered with the appliance.
The instructions for maintenance/service to be done by specialized
personnel, mandated by the manufacturer or the authorized repre­
sentative may be supplied in only one Community language which
the specialized personnel understand.
The instructions shall indicate the type and frequency of inspections
and maintenance required for safe operation including the preven­
tive maintenance measures.
English – 3 English – 3