Atlas Copco ICB-A21-07-06-HMI Mode D'emploi page 4

Safety Information
• Ensure that the joint conditions have not changed due to
events of influence.
• Be done after initial installation, maintenance or repair of
the equipment.
• Occur at least once per shift or at another suitable fre-
quency.
EU DECLARATION OF CONFORMITY
We, Atlas Copco Industrial Technique AB, SE-105 23
STOCKHOLM SWEDEN, declare under our sole responsi-
bility that the product (with name, type and serial number, see
front page) is in conformity with the following Directive(s):
2006/42/EC (MD), 2011/65/EU (RoHS), 2014/53/EU
(RED), 2015/863/EU (RoHS amendment)
Harmonized standards applied:
EN 300 328 V2.2.2, EN 301 489-1 V2.1.1, EN 301 489-17
V3.1.1, EN 301 893 V2.1.1, EN 55014-1:2017, EN
55014-2:2015, EN 61000-6-2:2005, EN
61000-6-3:2007+A1, EN 61000-6-4:2007+A1, EN
62841-1:2015, EN 62841-2-2:2015
Authorities can request relevant technical information from:
Aleksandra Duric, Product Compliance Manager, Atlas
Copco Industrial Technique AB, SE-105 23 Stockholm Swe-
den
Stockholm, 21 November 2022
Carl von Schantz, Managing Director
Signature of issuer
Noise and Vibration Declaration Statement
• Sound pressure level < 70 dB(A) , uncertainty 3 dB(A),
in accordance with ISO15744.
• Sound power level <80 dB(A) , uncertainty 3 dB(A), in
accordance with ISO15744.
• Vibration total value < 2.5 m/s
cordance with ISO28927-2.
These declared values were obtained by laboratory type test-
ing in accordance with the stated standards and are suitable
for comparison with the declared values of other tools tested
in accordance with the same standards. These declared values
are not adequate for use in risk assessments and values mea-
sured in individual work places may be higher. The actual ex-
posure values and risk of harm experienced by an individual
user are unique and depend upon the way the user works, the
workpiece and the workstation design, as well upon the expo-
sure time and the physical condition of the user.
We, Atlas Copco Industrial Technique AB, cannot be held
liable for the consequences of using the declared values, in-
stead of values reflecting the actual exposure, in an individual
risk assessment in a work place situation over which we have
no control.
4
2 2
, uncertainty - m/s , in ac-
© Atlas Copco Industrial Technique AB - 9834 5888 00
This tool may cause hand-arm vibration syndrome if its use is
not adequately managed. An EU guide to managing hand-arm
vibration can be found by accessing
index.php and selecting 'Tools' then 'Legislation'.
We recommend a programme of health surveillance to detect
early symptoms which may relate to noise or vibration expo-
sure, so that management procedures can be modified to help
prevent future impairment.
If this equipment is intended for fixtured applications:
The noise emission is given as a guide to the machine-
builder. Noise and vibration emission data for the com-
plete machine should be given in the instruction manual
for the machine.
WEEE
Information concerning Waste of Electrical and Electronic
Equipment (WEEE):
This product and its information, meets the requirements of
the WEEE directive/regulations (2012/19/EU), and must be
handled in compliance with the directive/regulations.
The product is marked with the following symbol:
Products marked with a crossed-out wheeled bin symbol and
a single black bar underneath, contain parts that must be han-
dled in compliance with the WEEE directive/regulations. The
entire product, or the WEEE parts, can be sent to your "Cus-
tomer Center" for handling.
RF Exposure Statement
This portable transmitter has been tested and found to comply
with FCC General Population RF Radiation Exposure limits
set forth for an uncontrolled environment and meets the FCC
radio frequency (RF) Exposure Guidelines. The antenna used
for this device must not be co-located or operating in conjunc-
tion with any other antenna or transmitter.
FCC and ISED Compliance Statement
This device complies with Part 15 of the FCC Rules. Any
changes or modifications not expressly approved by the man-
ufacturer could void the user´s authority to operate this de-
vice.
Operation is subject to the following two conditions:(1) this
device may not cause harmful interference, and (2) this device
must accept any interference received, including interference
that may cause undesired operation.
The device is only in compliance if no changes or modifica-
tions are made to the device. The antenna is fixed to the de-
vice and no change in antenna or fixation of the antenna is ac-
ceptable and such modification is considered to violate the
Compliance Statement.
FCC Responsible party:
Name: Rodney Hill
Position: Product Marketing Manager
ICB-A21-07-06-HMI
http://www.pneurop.eu/