Unpacking; Lawn Tractor With Side Discharge; Lawn Tractor With Rear Discharge; Installation - AL-KO Heckauswurf 220 l Instructions De Montage

Masquer les pouces Voir aussi pour Heckauswurf 220 l:
Table des Matières

Publicité

Les langues disponibles
  • FR

Les langues disponibles

  • FRANÇAIS, page 22

Unpacking

2 UNPACKING
The lawn tractor is supplied on a sturdy wooden
pallet.
2.1

Lawn tractor with side discharge

1. Place the pallet on level ground in order to
unpack the lawn tractor with side discharge.
2. Remove all accessory kits and the packaging
materials.
3. Remove the nails and screws from the board,
or knock them flat using a hammer so that
the tyres cannot be damaged.
4. Lift the tractor off the pallet (01/a) with the
front wheels.
5. Push the tractor backwards off the pallet (01/
b).
6. Secure the tractor to prevent it from rolling
away (e.g. with wheel chocks).
2.2

Lawn tractor with rear discharge

1. Place the pallet on level ground in order to
unpack the lawn tractor with side discharge.
2. Remove the bar of the grass catcher:
Rotate the bar downwards into the hori-
zontal position (01/a).
Press the bar downwards with light pres-
sure to release it from the locking mecha-
nism (01/b).
Remove the bar horizontally forwards
(01/c).
3. Remove all accessory kits and the packaging
materials.
4. Remove the nails and screws from the board,
or knock them flat using a hammer so that
the tyres cannot be damaged.
5. Lift the tractor out of the pallet (02/a) with the
front wheels.
6. Push the tractor from the pallet (02/b) back-
wards.
7. Secure the tractor to prevent it from rolling
away (e.g. with wheel chocks).

3 INSTALLATION

WARNING!
Danger if assembly is not carried out
completely!
Do not operate the lawn tractor before it
has been fully assembled!
Carry out all the work described in the
assembly instructions. If you are uncer-
tain about anything, ask a specialist to
confirm that the assembly has been car-
ried out correctly before the machine is
started up!
Check whether all safety and protective
devices are in place and functioning cor-
rectly!
The following assembly jobs must have been car-
ried out correctly before the lawn tractor can be
taken into operation as described in the operating
instructions:

Mounting the steering wheel

Mounting the operator's seat

Mounting the side discharge flap on the mow-
er plate*
Mounting the grass catcher**
Installing the starter battery
Fill with oil.
*: side discharge only, **: rear discharge only
3.1
Mounting the steering wheel
Side discharge: see Figure 02,
Rear discharge: see Figure 03.
1. Position the front wheels in the straight-
ahead position (a).
2. Place the clamping sleeve (b) on the steering
column.
3. Place the steering wheel (c) on the clamping
sleeve.
Note: Make sure the position is correct with
the spoke pointing towards the operator.
4. Insert the washer (d) and the cup spring (e).
5. Fix the steering wheel (c) in place using the
hexagon bolt (f).
Note: Make sure the tightening torque is
20 Nm + 5. Use a torque wrench.
6. Put on the cover (g).
3.2
Mounting the operator's seat
Side discharge: see image 03,
Rear discharge: see image 04.
1. Position the operator's seat.
15

Publicité

Table des Matières
loading

Ce manuel est également adapté pour:

Heckauswurf 250 lHeckauswurf 300 lSolo seitenauswurfSolo heckauswurf 220 lSolo heckauswurf 250 lSolo heckauswurf 300 l

Table des Matières