Dust/Chip Extraction; Switching On/Off; Practical Advice - Bosch GBH 180-LI Professional Notice Originale

As a requirement of the system, the SDS-plus application
tool can move freely. This causes a certain radial run-out at
no-load, which has no effect on the accuracy of the drill hole,
as the drill bit centres itself upon drilling.
Removing SDS-plus application tools (see figure B2)
– Push the locking sleeve (4) back and remove the applica-
tion tool.

Dust/Chip Extraction

Dust from materials such as lead-containing coatings, some
wood types, minerals and metal can be harmful to one's
health. Touching or breathing-in the dust can cause allergic
reactions and/or lead to respiratory infections of the user or
bystanders.
Certain dust, such as oak or beech dust, is considered carci-
nogenic, especially in connection with wood-treatment ad-
ditives (chromate, wood preservative). Materials containing
asbestos may only be worked by specialists.
– Provide for good ventilation of the working place.
– It is recommended to wear a P2 filter-class respirator.
Observe the relevant regulations in your country for the ma-
terials to be worked.
Avoid dust accumulation at the workplace. Dust can
u
easily ignite.
Operation
Start-up
Setting the Operating Mode
The operating mode of the power tool is selected using the
impact/mode selector switch (7).
– To change the operating mode, press the release
button (6) and turn the impact/mode selector switch (7)
until it clicks into the required position.
Note: Only change the operating mode when the power tool
is switched off. Otherwise, the power tool may become dam-
aged.
Position for hammer drilling into concrete or
stone
Position for drilling without impact in wood,
metal, ceramic and plastic and for screwdriv-
ing
Vario-Lock position for adjusting the chisel po-
sition
The impact/mode selector switch (7) will not
engage in this position.
Position for chiselling
Bosch Power Tools
Setting the rotational direction (see figure C)
The rotational direction switch (8) is used to change the ro-
tational direction of the power tool. However, this is not pos-
sible while the on/off switch (9) is being pressed.
Only operate the rotational direction switch (8) when
u
the power tool is not in use.
Always set the rotational direction to clockwise rotation for
hammer drilling, drilling and chiselling.
– Clockwise: To drill and to drive in screws, press the rota-
tional direction switch (8) all the way to the left.
– Anticlockwise: To loosen and unscrew screws and nuts,
press the rotational direction switch (8) all the way to the
right.

Switching On/Off

– To switch on the power tool, press the on/off switch (9).
The worklight (12) lights up when the on/off switch (9) is
lightly or fully pressed, allowing the work area to be illumin-
ated in poor lighting conditions.
– To switch off the power tool, release the on/off switch
(9).
For low temperatures, the power tool reaches the full ham-
mer/impact capacity only after a certain time.
Adjusting the Speed/Impact Rate
You can adjust the speed/impact rate of the power tool when
it is on by pressing in the on/off switch (9) to varying ex-
tents.
Applying light pressure to the on/off switch (9) results in a
low rotational speed/impact rate. Applying increasing pres-
sure to the switch increases the speed/impact rate.
Changing the chiselling position (Vario-Lock)
You can lock the chisel in 13 different positions, so you can
select the optimum working position for each task.
– Insert the chisel into the tool holder.
– Turn the impact/mode selector switch (7) to the "Vario-
Lock" position.
– Turn the application tool to the required chisel position.
– Turn the impact/mode selector switch (7) to the "chis-
elling" position. With this, the tool holder is locked.
– Set the rotational direction for chiselling to clockwise.

Practical Advice

Setting the drilling depth (see figure D)
You can use the depth stop (15) to set the required drilling
depth X.
– Press the button for depth stop adjustment (5) and insert
the depth stop into the auxiliary handle (14).
The fluting on the depth stop (15) must face downwards.
– Insert the SDS-plus application tool into the SDS-plus tool
holder (2) to the stop. Otherwise, the movability of the
SDS-plus drilling tool can lead to incorrect adjustment of
the drilling depth.
– Pull the depth stop far enough out that the distance
between the drill bit tip and the edge of the depth stop
corresponds to the required drilling depth X.
English | 9
1 609 92A 8EM | (04.01.2023)