Changing The Tool; Dust/Chip Extraction; Switching On/Off - Bosch GBH 180-LI Professional Notice Originale

16 | English
Make sure that the auxiliary handle is always
u
tightened. Otherwise you could lose control of the power
tool when working.
Swivelling the auxiliary handle (see figure A)
You can swivel the auxiliary handle (14) to any angle for a
safe work posture that minimises fatigue.
– Turn the lower gripping end of the auxiliary handle (14)
anticlockwise and swivel the auxiliary handle (14) into
the required position. Then turn the lower gripping end of
the auxiliary handle (14) clockwise to retighten it.
Make sure that the retaining strap of the auxiliary handle
slots into the corresponding groove of the housing.

Changing the Tool

The dust protection cap (3) largely prevents the penetration
of drilling dust into the tool holder during operation. When
inserting the tool, make sure that the dust protection cap (3)
does not become damaged.
Replace a damaged dust protection cap immediately.
u
It is recommended that you have use an after-sales
service for this.
Changing the tool (SDS plus)
Inserting SDS-plus application tools (see figure B1)
The SDS-plus drill chuck enables you to change the applica-
tion tool easily and conveniently without needing to use ad-
ditional tools.
– Clean and lightly grease the insertion end of the applica-
tion tool.
– Insert the application tool into the tool holder while turn-
ing it until it locks automatically.
– Check the latching by pulling the tool.
As a requirement of the system, the SDS-plus application
tool can move freely. This causes a certain radial run-out at
no-load, which has no effect on the accuracy of the drill hole,
as the drill bit centres itself upon drilling.
Removing SDS-plus application tools (see figure B2)
– Push the locking sleeve (4) back and remove the applica-
tion tool.

Dust/Chip Extraction

Dust from materials such as lead-containing coatings, some
wood types, minerals and metal can be harmful to one's
health. Touching or breathing-in the dust can cause allergic
reactions and/or lead to respiratory infections of the user or
bystanders.
Certain dust, such as oak or beech dust, is considered carci-
nogenic, especially in connection with wood-treatment ad-
ditives (chromate, wood preservative). Materials containing
asbestos may only be worked by specialists.
– Provide for good ventilation of the working place.
– It is recommended to wear a P2 filter-class respirator.
Observe the relevant regulations in your country for the ma-
terials to be worked.
Avoid dust accumulation at the workplace. Dust can
u
easily ignite.
1 609 92A 77K | (22.12.2021)
Operation
Start-up
Setting the Operating Mode
The operating mode of the power tool is selected using the
impact/mode selector switch (7).
– To change the operating mode, press the release
button (6) and turn the impact/mode selector switch (7)
until it clicks into the required position.
Note: Only change the operating mode when the power tool
is switched off. Otherwise, the power tool may become dam-
aged.
Position for hammer drilling into concrete or
stone
Position for drilling without impact in wood,
metal, ceramic and plastic and for screwdriv-
ing
Vario-Lock position for adjusting the chisel po-
sition
The impact/mode selector switch (7) will not
engage in this position.
Position for chiselling
Setting the rotational direction (see figure C)
The rotational direction switch (8) is used to change the ro-
tational direction of the power tool. However, this is not pos-
sible while the on/off switch (9) is being pressed.
Only operate the rotational direction switch (8) when
u
the power tool is not in use.
Always set the rotational direction to clockwise rotation for
hammer drilling, drilling and chiselling.
– Clockwise: To drill and to drive in screws, press the rota-
tional direction switch (8) all the way to the left.
– Anticlockwise: To loosen and unscrew screws and nuts,
press the rotational direction switch (8) all the way to the
right.

Switching On/Off

– To switch on the power tool, press the on/off switch (9).
The worklight (12) lights up when the on/off switch (9) is
lightly or fully pressed, allowing the work area to be illumin-
ated in poor lighting conditions.
– To switch off the power tool, release the on/off switch
(9).
For low temperatures, the power tool reaches the full ham-
mer/impact capacity only after a certain time.
Adjusting the Speed/Impact Rate
You can adjust the speed/impact rate of the power tool when
it is on by pressing in the on/off switch (9) to varying ex-
tents.
Bosch Power Tools