Drawing Up Lower Thread; Para Sacar El Hilo De La Canilla; Remontée Du Fil Inférieur - Brother XL5100 Manuel D'instructions

Table des Matières

Publicité

2
1
3
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○

Para sacar el hilo de la canilla

1. Levante el prensatelas y la aguja a sus posiciones más elevadas.
2. Con la mano izquierda, sujete el extremo del hilo superior. Con la
mano derecha, gire la ruedecilla hacia usted (en el sentido con-
trario al de las manecillas de un reloj) hasta que la aguja vaya
hacia abajo y suba a su posición más alta.
3. El hilo superior debe haber enganchado el hilo inferior en un lan-
zo. Tire del hilo superior hacia usted y el hilo inferior saldrá de la
canilla en un amplio enlace.
4. Tire unos 15 cm (6") de ambos hilos y colóquelos hacia la parte
posterior de la máquina, justo detrás del prensatelas. El hilo su-
perior debe pasar entre los salientes del prensatelas.
1 Hilo superior
2 Enlace del hilo inferior
3 Hilo inferior
31
1. Raise the presser foot and the needle to their highest positions.
2. With your left hand, hold the end of the upper thread. With your
3. The upper thread should have caught the lower thread in a loop.
4. Pull out about 15 cm (6") of both threads and place them toward
1
1. Lever au maximum le pied-de-biche et l'aiguille.
2. Avec la main gauche, tenir l'extrémité du fil supérieur. Avec la main
3. Le fil supérieur doit alors former une boucle avec le fil inférieur. Tirer
4. Tirer environ 15 cm de chacun des deux fils et les placer vers l'arrière

Drawing Up Lower Thread

right hand, turn the balance wheel toward you (counterclockwise)
until the needle moves down and back up again to its highest posi-
tion.
Pull the upper thread toward you and the lower thread will come
up from the bobbin in a large loop.
the back of the machine straight behind the presser foot. The upper
thread should pass between the toes of the presser foot.
1 Upper thread
2 Lower thread loop
3 Lower thread
Remontée du fil inférieur
droite, tourner le volant vers soi (dans le sens contraire aux aiguilles
d'une montre) jusqu'à ce que l'aiguille descende puis remonte à nou-
veau complètement.
vers soi le fil supérieur: le fil inférieur va se dérouler de la canette et
former une boucle de plus en plus large.
de la machine, juste derrière le pied-de-biche. Le fil supérieur doit pas-
ser entre les branches du pied-de-biche.
1 Fil supérieur
2 Boucle du fil inférieur
3 Fil inférieur

Publicité

Table des Matières
loading

Ce manuel est également adapté pour:

Xl5200Xl5300Px100Px200Px300

Table des Matières