Important - Enerpac Hushh 30 Serie Manuel D'instructions

IMPORTANT: Do not lift hydraulic equipment by the
hoses or swivel couplers. Use the carrying handle
or other means of safe transport.
CAUTION: Keep hydraulic equipment away from
flames and heat. Excessive heat will soften
packings and seals, resulting in fluid leaks. Heat
also weakens hose materials and packings. For optimum
performance do not expose equipment to temperatures of
65°C [150°F] or higher. Protect hoses and cylinders from
weld spatter.
DANGER: Do not handle pressurized hoses.
Escaping oil under pressure can penetrate the skin,
causing serious injury. If oil is injected under the
skin, see a doctor immediately.
WARNING: Only use hydraulic cylinders in a
coupled system. Never use a cylinder with
unconnected couplers. If the cylinder becomes
extremely overloaded, components can fail catastrophically
causing severe personal injury.
WARNING: BE SURE SETUP IS STABLE BEFORE
LIFTING LOAD.
Cylinders should be placed on a flat surface that can
support the load. Where applicable, use a cylinder base for
added stability. Do not weld or otherwise modify the
cylinder to attach a base or other support.
Avoid situations where loads are not directly
centered on the cylinder plunger. Off-center loads
produce considerable strain on cylinders and
plungers. In addition, the load may slip or fall, causing
potentially dangerous results.
SPECIFICATIONS
★ Flow vs. Pressure
Motor Voltage
Options
Motor Current
Draw
Relief Valve
Adjustment Range
Ambient
Temperature Range
Max. Recommended
Operating Fluid
Temperature
★ All flow data at 60 hz, 50 hz data will be 5/6 of this number.
30 Series
640 in.
3
60 in.
/min at 900-10,000 psi
1
[0,98 /min at 62-700 bar]
115-1-60
230-1-60
230-3-60
460-3-60
575-3-60
22 amps at max. pressure at 115-1-60
1 amps at max. pressure at 230-1-60
5.4 amps at max. pressure at 230-3-60
2.7 amps at max. pressure at 460-3-60
2.2 amps at max. pressure at 575-3-60
800-10,000 psi
[55-700 bar]
23°F to 104°F (-5°C to 40°C)
150°F (65,5°C)
Distribute the load evenly across the entire saddle
surface. Always use a saddle to protect the plunger.
IMPORTANT: Hydraulic equipment must only be
serviced by a qualified hydraulic technician. For
repair service, contact the Authorized ENERPAC
Service Center in your area. To protect your warranty, use
only ENERPAC oil.
WARNING: Immediately replace worn or damaged
parts by genuine ENERPAC parts. Standard grade
parts will break causing personal injury and
property damage. ENERPAC parts are designed to fit
properly and withstand high loads.
WARNING:
explosive atmosphere. Adhere to all local and
national electrical codes. A qualified electrician
must do installation and modification.
WARNING: Start the pump with the valve in the
neutral position to prevent accidental cylinder
operation. Keep hands clear of moving parts and
pressurized hoses.
WARNING:
relief valves, which must not be repaired or
adjusted except by an Authorized Enerpac Service
Center.
CAUTION:
motor, check specifications. Use of incorrect power
source will damage the motor.
40 Series
3
/min at 0-900 psi [10,5 1/min at 0-62 bar]
3
120 in. /min at 900-5,000 psi
1
[1,96 /min at 62-350 bar]
800-5,000 psi
[55-350 bar]
2
Do not use electric pumps in an
These pumps have factory adjusted
To prevent damage to pump electric
50 Series
3
120 in. /min at 900-10,000 psi
1
[1,96 /min at 62-700 bar]
230-3-60
460-3-60
575-3-60
10 amps at max. pressure at
230-3-60
5.0 amps at max. pressure at
460-3-60
4.7 amps at max. pressure at
575-3-60
800-10,000 psi
[55-700 bar]