Honeywell MP920B Instructions D'installation page 6

MP920B PNEUMATIC DAMPER ACTUATOR
AK3561
BALL JOINT
3/8 FLAT WASHER (2)
3/8 - 24
JAM NUT
SHOULDER
COUPLING
(3/8 - 16 TO 3/8 - 24)
11
3/8 - 16 NUT (2)
3/8 - 16 SET SCREW
OR THREADED ROD
(MAXIMUM 6 IN. LONG)
- NOT INCLUDED
1
MOUNT SWIVEL BRACKET TO OPERATOR
USING NUTS FROM BAG ASSEMBLY. LEAVE
NUTS HOLDING STUDS TO MP920 IN PLACE.
NOTE: IF NO POSITIONER GO TO
2
PLACE POSITIONER BETWEEN WELDS OF
MP920 AND FASTEN WITH BANDSTRAPS.
POSITIONER MUST CLEAR ALL
OBSTRUCTIONS INCLUDING THE MOUNTING
BRACKET.
3
MOUNT FEEDBACK LEVER AS SHOWN:
9/16 - 18 NUT (2)
9/16 IN. WASHER
END CAP
MP920B
4
HOOK FEEDBACK SPRING TO POSITIONER
AND TWIST UNTIL SQUARE NUT IS 3/16 IN.
(5 MM) FROM SCREW END. (SEE TEXT FOR
SPECIAL TOOL.)
5
HOOK SPRING THROUGH HOLE IN FEEDBACK
LEVER. MEASURE SPRING AND ADJUST
SQUARE NUT OR FEEDBACK LEVER POSITION
UNTIL SPRING LENGTH IS AS SHOWN.
10-5/8 ± 1/8 IN. (270 ± 3 MM)
FASTEN MOUNTING BRACKET OR OUTER
6
BRACKET IN PLACE ON FLOOR, WALL
FAN HOUSING OR PIPE.
95-6063EF
10
CRANKARM
3/8 SPLIT
LOCK WASHER
3/8 - 24 NUT
AK3557
10
CRANKARM
COTTERLESS
CLEVIS PIN
CLEVIS
3/8 - 16
11
3/8 - 16 NUT (2)
HITCH PIN
CLIP
OR
CLEVIS
3
FEEDBACK LEVER
(AIR END MOUNTING)
9/16 WASHER
6
ACTUATOR SHAFT
FEEDBACK LEVER
1/2 IN. (13 MM)
Fig. 8. Air end mounting (full swivel motion).
AK3559
7/8 ALLEN SOCKET
3/8 - 16 BOLT
HITCH PIN
3/8 WASHER
CLIP
SLEEVE
10
CRANKARM
CLEVIS
5/8 - 11
CLEVIS PIN
11
5/8 - 11 NUT (2)
3/8 WASHER
5/8 IN. THREADED ROD
(MAXIMUM 36 IN. LONG)
- NOT INCLUDED
OR
9/16 - 18 NUT
OR
FEEDBACK
SPRING
BAND
STRAP
MP920B
6
AK3560
3/8 FLAT
BALL JOINT WASHER (2)
3/8 - 24
JAM NUT
COUPLING
(5/8 - 11 TO 3/8 - 24)
AK3559
10
5/8 IN. THREADED ROD
CRANKARM (MAXIMUM 36 IN. LONG)
- NOT INCLUDED
CLEVIS
PIN
11
COUPLING
(9/16 - 18 TO
5/8 - 11)
SHOULDER
OR
5
14004345-001
POSITIONER KIT
POSITIVE
POSITIONER
CRANKARM
3/8 SPLIT
LOCK
WASHER
3/8 - 24 NUT
10
5/8 - 11 NUT (2)
11
COUPLING
(9/16 - 18 TO
5/8 - 11)
SHOULDER
4
2
SQUARE NUT
M18824