Publicité
Les langues disponibles
Les langues disponibles
Liens rapides
FITTING INSTRUCTIONS FOR CP0228BL CRASH PROTECTORS
HONDA CBR1000RR FIREBLADE 2008-
Page | 1
PICTURE 'A' 2008-11 MODEL
PICTURE 'B' 2008-11 MODEL
PICTURE 'C' 2012- MODEL
PICTURE 'D' 2012- MODEL
REAR OF BIKE
FRONT OF BIKE
PICTURE 'E'
R&G Racing
Unit 1, Shelley's Lane, East Worldham, Alton, Hampshire, GU34 3AQ
Tel: +44 (0)1420 89007 Fax: +44 (0)1420 87301
www.rg-racing.com
Email:
info@rg-racing.com
Publicité
Manuels Connexes pour R&G CP0228BL
Sommaire des Matières pour R&G CP0228BL
- Page 1 FITTING INSTRUCTIONS FOR CP0228BL CRASH PROTECTORS HONDA CBR1000RR FIREBLADE 2008- Page | 1 PICTURE ‘A’ 2008-11 MODEL PICTURE ‘B’ 2008-11 MODEL PICTURE ‘C’ 2012- MODEL PICTURE ‘D’ 2012- MODEL REAR OF BIKE FRONT OF BIKE PICTURE ‘E’ R&G Racing Unit 1, Shelley’s Lane, East Worldham, Alton, Hampshire, GU34 3AQ Tel: +44 (0)1420 89007 Fax: +44 (0)1420 87301 www.rg-racing.com...
-
Page 2: Left Hand Side
THIS KIT CONTAINS THE ITEMS PICTURED AND LABELLED BELOW. DO NOT PROCEED UNTIL YOU ARE SURE ALL PARTS ARE PRESENT. Please note that the way the kit is packed does not necessarily represent the way of mounting to the bike Page | 2 Please note that in cases where kits are packed with rubber washers holding the components onto the bolt –... -
Page 3: Right Hand Side
Page | 3 MARKING TOOL THIS KIT CONTAINS THE ITEMS PICTURED AND LABELLED BELOW. DO NOT PROCEED UNTIL YOU ARE SURE ALL PARTS ARE PRESENT. RIGHT HAND SIDE R&G Racing Unit 1, Shelley’s Lane, East Worldham, Alton, Hampshire, GU34 3AQ Tel: +44 (0)1420 89007 Fax: +44 (0)1420 87301 www.rg-racing.com Email:... -
Page 4: Tools Required
TOOLS REQUIRED Socket set to include 17mm and 19mm sockets and wrench. Set of metric Allen keys 4 and 5mm A/F. Torque wrench (up to 40Nm). Drill. 28mm Hole saw. Page | 4 LEGEND ITEM 1 = B0431 with CS340 (12mm) (BOTH CRASH PROTECTORS) (x2). ITEM 2 = BC0002 CRASH PROTECTOR CAPS (x2). - Page 5 Near side (left side as you sit on bike) Undo and remove side fairing screws (on the 2012 model remove the screw in position shown in pictures 1 and 2 then unclip the lower fairing locations). Gently support and ease fairing away from bike so a socket and wrench can be used to remove main engine bolt positioned as shown by bobbin positions and arrows on pictures A and C above (ensure frame/engine spacer stays in position).
- Page 6 Carefully open hole with 28mm hole-saw (on the 2012 model you will have to drill through the side fairing and the fairing trim care must be taken when drilling or a dremmel type tool may be used to remove the corner of the fairing trim).
-
Page 7: Conseil De Montage
Notice de montage CP0228 HONDA 1000 CBR RR 2008- Page | 7 Le sens de montage n'est pas identique au sens présenté dans l'emballage, merci de suivre les instructions ci dessous. Dans le cas où les kits sont emballés avec un joint torique, celui-ci doit être retiré avant le montage. - Page 8 FITTING INSTRUCTIONS FOR CP0228BL CRASH PROTECTORS HONDA CBR1000RR FIREBLADE 2008- GAUCHE : – Page | 8 Déserrez et enlevez les vis de fixation du carénage. (sur le modèle 2012 retirez la vis dans la position indiquée sur les images 1 et 2, puis déclipser les emplacements de carénage inférieur).
- Page 9 – Serrez la vis jusqu'à ce que vous sentiez de la compression à l'intérieur de la protection. Tournez encore un peu et vous sentirez la compression augmenter, faite un quart de tour. Ne pas trop serrer car cela pourrait abîmer les filetages de la moto Ne pas exéder 40nm de couple de serrage. –...
- Page 10 – Serrez la vis jusqu'à ce que vous sentiez de la compression à l'intérieur de la protection. Tournez encore un peu et vous sentirez la compression augmenter, faite un quart de tour. Ne pas trop serrer car cela pourrait abîmer les filetages de la moto Ne pas exéder 40nm de couple de serrage. –...