Télécharger
Partager
Imprimer la page
R&G CP0265 Instructions De Montage
  1. Manuels
  2. Marques
  3. R&G Manuels
  4. Accessoires de moto
  5. CP0265
  6. Instructions de montage

R&G CP0265 Instructions De Montage

For honda vfr1200 2010
Masquer les pouces
1
2
3
4
5
6
7

Liens rapides

Télécharger ce manuel
FITTING INSTRUCTIONS FOR CP0265 CRASH PROTECTORS
HONDA VFR1200 2010
REAR OF BIKE
FRONT OF BIKE
PICTURE 'C'
THIS KIT CONTAINS THE ITEMS PICTURED AND LABELLED BELOW.
DO NOT PROCEED UNTIL YOU ARE SURE ALL PARTS ARE PRESENT.
Please note that the way the kit is packed does not necessarily represent the way of
mounting to the bike
Please note that in cases where kits are packed with rubber washers holding the components onto
the bolt – the rubber washers should be thrown away!
R&G Racing
Unit 1, Shelley's Lane, East Worldham, Alton, Hampshire, GU34 3AQ
Tel: +44 (0)1420 89007 Fax: +44 (0)1420 87301
www.rg-racing.com
Email:
info@rg-racing.com
loading

Manuels Connexes pour R&G CP0265

Sommaire des Matières pour R&G CP0265

  • Page 1 FITTING INSTRUCTIONS FOR CP0265 CRASH PROTECTORS HONDA VFR1200 2010 REAR OF BIKE FRONT OF BIKE PICTURE ‘C’ THIS KIT CONTAINS THE ITEMS PICTURED AND LABELLED BELOW. DO NOT PROCEED UNTIL YOU ARE SURE ALL PARTS ARE PRESENT. Please note that the way the kit is packed does not necessarily represent the way of...

  • Page 2: Left Hand Side

    HE PARTS SHOWN MAY BE REPRESENTATIVE ONLY FOR CLARITY OF INSTRUCTIONS ONLY M12 PLAIN SHAKE-PROOF WASHER (x2) WASHER (LW0001) (x1) M12 NYLOC NUT (x1) ENGINE BAR 232mm LONG (EB038) (x1) BUBBLE STICKERS (RG0005) (x2) PROTECTOR CAP SPACER (BC0002) (x1) (S0371) (x1) OU WILL ALSO HAVE A TEMPLATE CRASH-PROTECTOR TO AID IN POSITIONING HOLE FOR...

  • Page 3: Tools Required

    TOOLS REQUIRED  Socket set to include 17mm and 19mm sockets and wrench.  Torque wrench (up to 40Nm).  28mm Hole-saw and/or dremmel type tool.  Masking tape. Near side (left side as you sit on bike)  Cut out line of template for left-hand side and using masking tape secure in position as shown above (using edges and cut-out as a guide).
  • Page 4 Off side (right side as you sit on bike)  Cut out line of template for right-hand side and using masking tape secure in position as shown above (using edges and cut-out as a guide).  Carefully mark centre position of hole, remove template and pilot drill (approximately 6mm diameter).
  • Page 5 FRANCE INSTRUCTIONS DE MONTAGE DES PROTECTIONS CP0265 HONDA VFR1200 2010 ARRIERE AVANT ‘C’ LIRE LA NOTICE AVANT DE COMMENCER LE MONTAGE DES PROTECTIONS ’ ’ R&G A PRESENTATION DES PIECES DANS L EMBALLAGE N EST PAS TOUJOURS IDENTIQUE AU SENS DE MONTAGE Merci de noter que dans le cas où...
  • Page 6 Ensuite glisser l’ensemble à travers l’un des tampons R&G. (les rondelles et l’écrou seront  positionnés dans le renfoncement du tampon). Glisser ensuite l’entretoise R&G contre contre le tampon. (la partie de l’entretoise la plus large  sera positionnée contre le tampon). Vérifier ensuite que la partie de la barre R&G qui ressort du tampon et de l’entretoise est égale à...
  • Page 7 Attention au sens de montage, la partie la plus large du tampon sera positionnée vers l’avant de la  moto. (voir photo C)  Clipper le cache R&G dans le tampon. (voir photo C) R&G Racing Unit 1, Shelley’s Lane, East Worldham, Alton, Hampshire, GU34 3AQ Tel: +44 (0)1420 89007 Fax: +44 (0)1420 87301 www.rg-racing.com Email:...