Husqvarna 325R Manuel D'utilisation page 12

• Tighten the fuel tank cap carefully or a fire can
occur.
• Move the product at a minimum of 3 m (10 ft) from
the position where you filled the tank before a start.
• Do not put too much fuel in the fuel tank.
• Make sure that a leak cannot occur when you move
the product or fuel container.
• Do not put the product or a fuel container where
there is an open flame, spark or pilot light. Make
sure that the storage area does not contain an open
flame.
• Only use approved containers when you move the
fuel or put the fuel into storage.
• Empty the fuel tank before long-term storage. Obey
the local law on where to dispose fuel.
• Clean the product before long-term storage.
• Remove the spark plug cap before you put the
product into storage to make sure that the engine
does not start accidentally.
Introduction
WARNING:
product, you must read and understand the
safety chapter.
WARNING:
cable from the spark plug before you
assemble the product.
To assemble the handlebar
1. Remove the screw behind the throttle handle. (Fig.
26)
2. Move the throttle handle to the right side of the
handlebar.
3. Align the hole behind the throttle handle with the
hole in the handlebar.
4. Put the screw go through the holes. Tighten the
screw.
5. Attach the handlebar between the arrows on the
shaft. Tighten the screw. (Fig. 27)
To attach the harness clamp
1. Put the harness clamp on the shaft with the loop of
the harness clamp up. Put the harness clamp above
the arrows on the shaft.
2. Put the throttle wire in the groove of the harness
clamp at bottom.
3. Align the harness clamp screw holes.
4. Attach 2 screws into the screw holes.
5. Tighten the screws.
12
Assembly
Before you assemble the
Remove the spark plug
Safety instructions for maintenance
WARNING:
instructions that follow before you do
maintenance on the product.
• Do only the maintenance and servicing given in
this operator's manual. Let professional servicing
personnel do all other servicing and repairs.
• Regularly do the safety checks, maintenance and
service instructions given in this manual. Regular
maintenance increases the life of the product
and decreases the risk of accidents. Refer to
Maintenance schedule on page 15 for instructions.
• If the safety checks in this operator's manual is
not approved after you do maintenance, speak to
your servicing dealer. We guarantee that there are
professional repairs and servicing available for your
product.
To assemble the cutting attachment
To assemble the cutting attachment guard
1. Put the cutting attachment guard (A) onto the shaft.
(Fig. 28)
2. Put the bracket (B) in the slot on the cutting
attachment guard.
3. Attach the bolt (C) through the hole on the bracket to
the cutting attachment guard.
To assemble the grass blade
1. Make sure that the cutting attachment guard (A) is
attached to the product. Refer to
cutting attachment guard on page 12 . (Fig. 29)
2. Put the locking pin (B) in the hole to lock the shaft.
3. Put the blade (E), support cup (F) and support flange
(G) on the output shaft (D).
4. Make sure that the drive disc (C) engages correctly
in the center hole of the blade. (Fig. 30)
5. Put the locknut (H) on the output shaft. Hold the
shaft of the combination wrench near the cutting
attachment guard. Turn the combination wrench
counterclockwise to tighten the locknut. Torque the
locknut to 35-50 Nm / 26-36 ft/lb.
6. Remove the locking pin.
To attach the trimmer head
1. Make sure that the cutting attachment guard (A) is
attached to the product. Refer to
cutting attachment guard on page 12 . (Fig. 31)
2. Make sure that the drive disc (C) is attached to the
output shaft (D).
3. Put the locking pin (B) in the hole to lock the shaft.
Read the warning
To assemble the
To assemble the
881 - 002 - 24.06.2022