Operating The Main Menu; Configuration The Main Menu (Av Input) - JVC DLA-M5000LE Manuel D'instructions

Operating the Main Menu

Configuration the Main Menu (AV Input)

You can adjust video quality (PICTURE) and etc. using the menus.
The menus are configured as follows: Main menu (AV inputs: During EXT. IN input signal)
Main menu (AV inputs: During EXT. IN input signal)
TRACKING:
PIXEL CLOCK
PHASE:
POSITION V. POS.:
H. POS.:
PICTURE BRIGHTNESS:
CONTRAST:
SHARPNESS:
COLOR:
TINT:
ALL RESET:
OPTIONS MENU AUTO OFF:
LINE DISPLAY:
RIGHT LEFT REV.:
TOP BOTTOM INV.:
CLAMP:
RESIZE:
BACK COLOR:
COLOR TEMP.:
ASPET CHANGE:
SLEEP TIME:
LAMP TIME:
SOURCE: Normally used in AUTO. If use in AUTO is unstable such as color not appearing, the screen being disturbed or the
screen being intermitted, set to the dedicated source (forced mode) in accordance with the input signal.
USER allows you to set a source which is uniquely adjusted by the user.
CHANNEL: Sets a line and multiple sources for each channel.
USER SOURCE Sets up an area for the source being input, and registers the user name.
SET UP:
DISPLAY SIZE: This does not work for AV [EXT. IN (VIDEO, Y/C, YPBPR)] input signals. (Adjustment items are displayed in gray
color).
DECODER: Normally, set to AUTO. The color system of an input signal is automatically identified and shown in ( ). When use in
AUTO is unstable such as no color being shown, set the dedicated color system in accordance with the input signal.
You can select from AUTO, NTSC(480i), NTSC4.43, PAL, and SECAM.
LANGUAGE: Text on the screen can be changed to a language other than English. Languages that can be displayed are the
following six:
(Italian), and FRANÇAIS (French). However, some text such as "QUICK-ALIGNMENT" (Quick-Alignment), etc. are
shown only in English.
30
Normally, no adjustment is required. The lateral size and display area of video image are
adjusted.
Normally, no adjustment is required. Flickering or dim video image is adjusted.
The vertical position of the video image being projected is adjusted.
The horizontal position of the video image being projected is adjusted.
The brightness of the video image being projected is adjusted.
The contrast of the video image being projected is adjusted.
The sharpness of the video image being projected is adjusted.
The color density of the video image being projected is adjusted.
The tint of the video image being projected is adjusted. (Displayed only for NTSC signal)
All the items adjusted are reset.
Sets whether to turn off menu display automatically (YES) or not (NO).
Sets whether to make the line display effective (ON) or not (OFF) for about 5 seconds
after input switching.
Video image is reversed right-to-left.
Video image is inverted top-to-bottom.
Sets the clamp pulse's position at the back porch (BP) or on the sink tip (ST). Normally,
the clamp pulse is used at BP. If, with some PCs or workstations, the screen becomes
unstable such as being too dark or too bright, try to switch to ST.
Does not work with AV (video) input. (RESIZE is shown in gray.)
Specifies the background color when there is no video signal. Background color can be
selected from BLUE, CYAN, BLACK, GREEN, MAGENTA, RED, and YELLOW.
Adjusts the color temperature of the image being projected. Make adjustment when the
image becomes reddish or bluish.
Color temperature can be set to LOW, MIDDLE, or HIGH.
Selects the vertical-to-horizontal ratio of the image projected. The factory-set ratio is 4 : 3.
When projecting high-vision video image, a ratio of 16 : 9 can be selected.
Sets the length of sleep time. A set sleep time after input signal is depleted, the projector
goes into a stand-by state. Sleep time can be selected from 10 minutes, 20 minutes, 30
minutes, 60 minutes and 0 minutes. (If you select 0 minutes, the sleep time will be
cleared.)
Indicates the accumulated used hours of the light-source lamp.
N N N N
(Japanese), ENGLISH (English), DEUTSCH (German), ESPAÑOL (Spanish), ITALIANO
For computer inputs, see the following page.