Safety Warnings; Before Operating Chain Saw; Kickback; Kickback Safety Devices On This Saw - Remington 100582-01 Mode D'emploi

Table des Matières

Publicité

Les langues disponibles

Les langues disponibles

!

SAFETY WARNINGS

WARNING ICON
G 001
Read and understand all Safety Warnings on pages
3 and 4. Improper use of this chain saw can cause
severe injury or death from fire, electrical shock,
body contact with moving chain, or falling wood.

BEFORE OPERATING CHAIN SAW

1. Read and understand this owner's manual before operating
chain saw.
2. Use chain saw for cutting wood only. Do not use for
cutting any non-wood items.
3. Only well-instructed adults should operate chain saw. Never
allow children to operate chain saw. First-time user should
obtain informed, practical instruction in addition to reading
this manual. Practice cutting logs on a saw horse or cradle.
4. Use only electrical voltage noted on model plate of chain saw.
5. Use only extension cords marked for outdoor use. See
page 8 for extension cord requirements.
6. Do not operate chain saw
• while under the influence of alcohol, medication, or drugs
• in rain or in damp or wet areas
• where highly flammable liquids or gases are present
• if saw is damaged, adjusted wrong, or not fully assembled
• if trigger does not turn saw on and off. Chain must stop
moving when you release trigger. Have faulty switch
replaced by authorized service person.
• while tired or in a hurry
• while in tree or on a ladder unless trained to do so
7. Wear snug-fitting clothes when operating chain saw. Do
not wear loose clothing or jewelry. They can get caught in
moving saw chain.
8. Wear the following safety gear when operating chain saw:
• heavy-duty gloves (wear rubber gloves if working outdoors)
• steel-toed safety footwear with non-skid soles
• eye protection such as safety glasses, goggles, or face screen
• safety hard hat
• ear mufflers or ear plugs
• hair covering to contain long hair
• face or dust mask (if working in dusty areas)
9. Before cutting, always provide the following:
• clear work area
• secure footing
• planned retreat path from falling tree
10.Inspect tree before cutting down. Make sure there are no
dead limbs or branches that may fall on you.

KICKBACK

!
WARNING
WARNING ICON
G 001
Avoid Kickback. Kickback can cause you to lose
control of chain saw. Kickback can cause severe
injury or death.

Kickback Safety Devices On This Saw

This saw has a low-kickback chain and reduced-kickback
guide bar. Both items reduce the chance of kickback. Kick-
back can still occur with this saw. Do not let tip of guide bar
touch anything when chain is moving.
101241
All manuals and user guides at all-guides.com
This saw has a chain brake. When kickback occurs, the front
hand guard is moved forward by the back of operator's left
hand. This stops the saw chain quickly, reducing the chance of
serious injury.
Never hold the chain saw by the front hand guard.
Cause Of Kickback
Kickback may occur when nose or tip of guide bar touches an
object while chain is moving. If chain cutter catches on object,
a sudden reverse action will result. The guide bar will kick up
and back towards operator.
Kickback may also occur when wood pinches chain at guide
bar nose. A sudden reverse action will also result.
The following steps will reduce the risk of kickback:
• Use both hands to grip saw while saw is running. Use firm
grip. Thumbs and fingers must wrap around saw handles.
• Keep all safety items in place on saw. Make sure they
work properly.
• Do not overreach or cut above shoulder height.
• Keep solid footing and balance.
• Stand slightly to left side of saw. This keeps your body
from being in direct line with chain.
• Do not let guide bar nose touch anything when chain is
moving (see Figure 1).
Direction
90°
Quadrant
Figure 1 - Kickback Hazard Example. Do Not Let Nose of
Guide Bar Touch Object While Chain is Moving
• Never try cutting through two logs at same time. Only cut
one log at a time.
• Do not bury guide bar nose or try plunge cut (boring into
wood using guide bar nose).
• Watch for shifting of wood or other forces that may pinch
chain.
• Use extreme caution when re-entering a previous cut.
• Use low-kickback chain and guide bar supplied with this
chain saw. Only replace these parts with chains and guide
3
Do Not Let
Guide Bar Nose
Touch Here
3
Continued

Publicité

Table des Matières
loading

Ce manuel est également adapté pour:

100582-02

Table des Matières