Prepare The Machine - GGP ITALY BL 2.6 E Manuel D'utilisation

6
EN
D) MAINTENANCE AND STORAGE
1) Keep all nuts, bolts and screws tight to be sure the
equipment is in safe working condition. Routine main-
tenance is essential for safety and for maintaining a
high performance level.
2) Do not perform any work on the machine that is not
described in this manual unless adequately skilled with
appropriate tools.
3) Allow the motor to cool down before storing in any
enclosure.
4) To reduce fire risks, do not leave containers with de-
bris inside a room.
5) Wear work gloves when performing all maintenance.
6) For safety reasons, never use the machine with worn
or damaged parts. Damaged parts are to be replaced
and never repaired. Only use original spare parts. Parts
that are not of the same quality can seriously damage
the equipment and compromise safety.
7) Before putting the machine away, check you have re-
moved wrenches or tools used for maintenance.
8) Store the machine out of the reach of children.
9) Often inspect the bag to avoid wear and a decrease
in quality.
E) ADDITIONAL WARNINGS
1) Before each use, check the machine for damage. Any
repairs must be done at a specialised centre. Turn off
the machine and disconnect the plug from the socket if
the machine begins to vibrate abnormally, then contact
a specialised centre for inspection.
2) Parts subject to wear must only be replaced at a
specialised centre.
3) Never use the machine if the power cable or exten-
sion cable are damaged or worn.
4) Never connect a damaged cable to a mains socket
and never touch a damaged cable that is connected to
the mains socket. Damaged or deteriorated cables
may cause contact with energised parts.
5) If the machine's power cable is damaged, it can only
be replaced with an original spare part by your dealer or
an authorised service centre.
6) Power up the machine using a differential switch
(RCD - Residual Current Device) with a tripping current
of max. 30 mA.
7) The permanent connection of any electrical equip-
ment to the mains of a building must be installed by a

4. PREPARE THE MACHINE

The machine can be used as both a blower and a
vacuum collector; for both of these uses it is nec-
essary to correctly arrange the appropriate acces-
sories included with the equipment.
WARNING!
Unpacking and complet-
ing the assembly should be done on a flat and
stable surface, with enough space for moving
the machine and its packaging, always making
use of suitable equipment.
Disposal of the packaging should be done in ac-
cordance with the local regulations in force.
SAFETY WARNINGS / PREPARE THE MACHINE
All manuals and user guides at all-guides.com
qualified electrician in conformity with the regulations in
force. Incorrect wiring can cause serious injury and
even death.
8) WARNING: DANGER! Moisture and electricity are
not compatible:
– always handle and connect electric cables in dry con-
– never allow electric sockets or cables to contact wet
– connections between cables and sockets must al-
9) The quality of the extension leads must be no less
than H07RN-F or H07VV-F, with a minimum section of
1.5 mm
10) Attach the extension lead to the cable fastener be-
fore starting the machine.
11) Never pass the vacuum tube over an electric cable.
Use the cable fastener to prevent the cable from dis-
connecting accidentally as indicated in this manual.
Make sure it is connected to the socket without being
forced.
12) Never pull the machine by its power cable or use
the cable to pull the plug. Do not expose the cable to
sources of heat, or let it come into contact with oil, sol-
vents and sharp objects.
F) TRANSPORTATION AND HANDLING
1) Whenever the machine is to be handled or trans-
ported you must:
– turn off the motor;
– only hold the machine using the handgrips and posi-
tion the tubes so that they do not obstruct.
2) When moving the machine by motor vehicle, re-
move the pipes and position so it is not a hazard for any-
one and secure it firmly to prevent it from turning over.
G) ENVIRONMENTAL PROTECTION
1) Dispose of the packaging and waste materials in
accordance with the local laws in force.
2) At the time of decommissioning, do not pollute the
environment with the machine, hand it over to a disposal
centre, in accordance with the local laws in force.
1. TO USE AS A BLOWER (Fig. 1)
– Apply the intake grille (1) to the power unit (2),
– Attach the intake grille (1) to the power unit (2)
– Align the blower tube (5) to the opening of the
ditions;
areas (puddles or wet grass);
ways be watertight. Only use extension leads with in-
tact, watertight and approved sockets sold on the
market.
and a recommended maximum length of 25 m.
2
positioning it as indicated and turning it 90°
clockwise.
fastening it to the catch (3) with the specific lever
(4).
power unit and push it to the end until it firmly
locks into place.