General Power Tool Safety Warnings - GGP ITALY BL 2.6 E Manuel D'utilisation

4
EN

GENERAL POWER TOOL SAFETY WARNINGS

WARNING!
Read all safety warnings
and all instructions. Failure to follow the war-
nings and instructions may result in electric
shock, fire and/or serious injury.
Save all warnings and instructions for future ref-
erence. The term "power tool" in the warnings refers
to your mains-operated (corded) power tool.
1) Work area safety
a) Keep work area clean and well lit. Cluttered or
dark areas invite accidents.
b) Do not operate power tools in explosive at-
mospheres, such as in the presence of flam-
mable liquids, gases or dust. Power tools create
sparks which may ignite the dust or fumes.
c) Keep children and bystanders away while op-
erating a power tool. Distractions can cause you
to lose control.
2) Electrical safety
a) Power tool plugs must match the outlet. Never
modify the plug in any way. Do not use any
adapter plugs with earthed (grounded) power
tools.
Unmodified plugs and matching outlets will reduce
risk of electric shock.
b) Avoid body contact with earthed or grounded
surfaces, such as pipes, radiators, ranges and
refrigerators. There is an increased risk of electric
shock if your body is earthed or grounded.
c) Do not expose power tools to rain or wet con-
ditions. Water entering a power tool will increase
the risk of electric shock.
d) Do not use the cord improperly. Never use the
cord for carrying, pulling or unplugging the po-
wer tool. Keep cord away from heat, oil, sharp
edges or moving parts. Damaged or entangled
cords increase the risk of electric shock.
e) When operating a power tool outdoors, use an
extension cord suitable for outdoor use. Using
a cord suitable for outdoor use reduces the risk of
electric shock.
f) If operating a power tool in a damp location is
unavoidable, use a residual current device
(RCD) protected supply. Using an RCD reduces
the risk of electric shock.
3) Personal safety
a) Stay alert, watch what you are doing and use
common sense when operating a power tool.
Do not use a power tool while you are tired or
under the influence of drugs, alcohol or med-
ication. A moment of inattention while operating
power tools may result in serious personal injury.
b) Use personal protective equipment. Always
wear eye protection. Protective equipment such
as dust mask, non-skid safety shoes, hard hat, or
All manuals and user guides at all-guides.com
c) Prevent unintentional starting. Ensure the
d) Remove any adjusting key or wrench before
e) Do not overreach. Keep proper footing and
f) Dress properly. Do not wear loose clothing or
4) Power tool use and care
a) Do not force the power tool. Use the correct
b) Do not use the power tool if the switch does
c) Disconnect the plug from the power source be-
d) Store idle power tools out of the reach of chil-
e) Maintain power tools. Check for misalignment
f) Keep cutting tools sharp and clean. Properly
g) Use the power tool, accessories and tool bits
5) Service
a) Have your power tool serviced by a qualified
hearing protection used for appropriate conditions
will reduce personal injuries.
switch is in the off-position before connecting
to power source, picking up or carrying the
tool. Carrying power tools with your finger on the
switch or energising power tools that have the
switch on invites accidents.
turning the power tool on. A wrench or a key left
attached to a rotating part of the power tool may re-
sult in personal injury.
balance at all times. This enables better control
of the power tool in unexpected situations.
jewellery. Keep your hair, clothing and gloves
away from moving parts. Loose clothes, jew-
ellery or long hair can be caught in moving parts.
power tool for your application. The correct po-
wer tool will do the job better and safer at the rate
for which it was designed.
not turn it on and off. Any power tool that cannot
be controlled with the switch is dangerous and
must be repaired.
fore making any adjustments, changing ac-
cessories, or storing power tools. Such pre-
ventive safety measures reduce the risk of starting
the power tool accidentally.
dren and do not allow persons unfamiliar with
the power tool or these instructions to operate
the power tool. Power tools are dangerous in the
hands of untrained users.
or obstruction of moving parts, breakage of
parts and any other condition that may affect
the power tool's operation. If damaged, have
the power tool repaired before use. Many acci-
dents are caused by poorly maintained power
tools.
maintained cutting tools with sharp cutting edges
are less likely to become jammed and are easier to
control.
etc. in accordance with these instructions, ta-
king into account the working conditions and
the work to be performed. Using the power tool
for operations other than those intended could re-
sult in a hazardous situation.
repair person using only identical replacement
parts. This will ensure that the safety of the power
tool is maintained.
SAFETY WARNINGS