Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
.
rests safely against the end stop bolts.
rests safely against the end stop bolts.
1.
Unscrew the cup grinding wheel on the bottom using a suitable tool and hold it with one hand.
Unscrew the cup grinding wheel on the bottom using a suitable tool and hold it with one hand.
Unscrew the cup grinding wheel on the bottom using a suitable tool and hold it with one hand.
rests safely against the end stop bolts.
.
rests safely against the end stop bolts.
2.
Pull the cup grinding wheel including the spring washer off the motor axle.
Pull the cup grinding wheel including the spring washer off the motor axle.
3.
Slip the new cup grinding wheel including the spring washer onto the motor axle and tighten it.
Slip the new cup grinding wheel including the spring washer onto the motor axle and tighten it.
Slip the new cup grinding wheel including the spring washer onto the motor axle and tighten it.
Tightening torque for M8 => 25Nm .
Tightening torque for M8 => 25Nm
8 Maintenance
Pos : 9.3 /KN2006- SM/War tung/002 1 Sic herheit_Titel @ 9\mod_1144434831619_1.doc @ 86810
8.1 Safety
Pos: 9.4 /KN2006-SM/Wartung/003 1.1.0 Personal --> Standard -- > ggf. anpassen @ 9
Unless specified otherwise, the maintenance steps des
Unless specified otherwise, the maintenance steps described herein can be performed by the operator.
Personnel
Some maintenance steps may only be performed by specially trained qualified personnel or the
Some maintenance steps may only be performed by specially trained qualified personnel or the
Some maintenance steps may only be performed by specially trained qualified personnel or the
manufacturer. These steps will be pointed out separately in the description of the individual maintenance
manufacturer. These steps will be pointed out separately in the description of the individual maintenance
manufacturer. These steps will be pointed out separately in the description of the individual maintenance
steps.
All work on the electrical system must be performed by trained electricians.
All work on the electrical system must be performed by trained electricians.
Wear the following protective equipment when performing maintenance:
Wear the following protective equipment when performing maintenance:
Personal
protective
Protective clothing
Protective clothing
equipment
Safety shoes
Safeguard
against restart
10.03.2009
All manuals and user guides at all-guides.com
Also make sure that the curved
Also make sure that the curved knife is securely clamped into the horizontal clamping device and
Also make sure that the curved knife is securely clamped into the horizontal clamping device and
Also make sure that the curved
IMPORTANT!
IMPORTANT!
Mark the cup grinding wheel as used and dispose of it!
DANGER!
DANGER!
The new cup grinding wheel must not be exposed to blows!
The new cup grinding wheel must not be exposed to blows!
RISK of bursting during operation!
> ggf. anpassen @ 9 \mod_1144434832402_1.doc @ 86817
DANGER!
DANGER!
Risk of fatal injury caused by unauthorized restart!
Risk of fatal injury caused by unauthorized restart!
Performing maintenance work always involves the risk of the power supply being switched
Performing maintenance work always involves the risk of the power supply being switched
Performing maintenance work always involves the risk of the power supply being switched
on without authority. This may cause fatal injuries to any person
on without authority. This may cause fatal injuries to any person inside the hazard area of
the machine.
the machine.
Therefore:
Therefore:
–
Switch off all power supplies and secure them against restart before commencing any
Switch off all power supplies and secure them against restart before commencing any
work.
Knife sharpener MS 100
Knife sharpener
is securely clamped into the horizontal clamping device and
is securely clamped into the horizontal clamping device and
cribed herein can be performed by the operator.
inside the hazard area of
Maintenance
27
Publicité
Table des Matières
