Operation And Maintenance - Campingaz ATTITUDE 2100 LX Utilisation Et Entretien

Attitude 2100 LX
GB
(1) Lid
(2) Thermometer
(3) Culinary modular grid
(4) Griddle
(5) Instaclean
(6) Battery AA x 1
(7) Electronic ignitor
(8) Gas connection
(9) Handle for carriage
(10) Foot
(11) Rubber pad for foot
(12) Button for electronic ignition
(13) Knob
(14) Electrodes for ignition
(15) Grease tray
NOTE: Unless otherwise specified, following generic terms "appliance / unit / product / equipment / device" appeared
in this instruction manual all refer to the product "Campingaz
• IMPORTANT: Read these instructions for use carefully so as to familiarize yourself with the appliance before
connecting it to its gas container. Keep these instructions for future reference.
• Use outdoors only
• Do not use charcoal or lava rock.
• Do not use an adjustable low pressure regulator. Use fixed regulators that comply with the European standard
concerning them.
• Never put a metal plate, that has neither been designed nor recommended by Campingaz
cooking grids.
Follow these instructions carefully to avoid seriously damaging your barbecue.
a) FOR YOUR SAFETY
- Install your appliance and the gas cylinder on a flat,
stable and non-flammable surface. If you use your
appliance on grass, check that it is not too high and that
it does not come into contact with the burner flame to
avoid any risk of fire.
- Use the device on a stable, flat and horizontal support
that is rigid enough to support the weight of the device
(table). Position the gas cylinder on the ground.
- Regardless of height H, the width or diameter D of the
cylinder (Fig. 1), the gas cylinder must be placed at least
30 cm away from your appliance.
- Do not store or use petrol and other flammable liquids or
vapours in the vicinity of this barbecue. If you smell gas:
1) Close the valve of the cylinder
2) Extinguish all naked flames
3) Open the lid
4) If the smell continues ,see "g Checking for gas leaks"
or immediately seek advice from your local retailer.
- Parts which are protected by the manufacturer or the
manufacturer's representative must not be manipulated
by the user.
- Close the gas container after use.
- This barbecue must only be used outdoors.
- CAUTION: accessible parts may get very hot. Keep
young children away.
- There should be no combustible materials within a
radius of approximately 60 cm around the barbecue
- Do not move the barbecue when alight.
- The appliance should be operated on a level surface.
- Estimated air offtake 2 m
- Some parts of your barbecue may be hot during and
immediately after their use: the lid, grill, grease pan, etc.
Wear gloves when handling.

Operation and maintenance

/kW/h.
3
Attitude 2100 EX
See page 2
(1) Lid
(2) Warming rack
(3) Culinary modular grid
(4) Griddle
(5) Instaclean
(6) Battery AA x 7
(7) Battery compartment
(8) Gas connection
(9) Handle for carriage
(10) Backlighting device
(11) Foot
(12) Rubber pad for foot
(13) Digital thermometer
(14) Knob
(15) Probes for thermometer
(16) Electrodes for ignition
(17) Grease tray
Attitude 2100 LX/EX".
®
b) ASSEMBLY
Check and remove all components from the box.
Cooking grids and griddles (Fig. 2)
Assemble the cooking grids and griddles on the grill:
the grid with the culinary modular system is installed on
the left and the reversible griddle on the right. Install the
griddle first. The right side of the grid with culinary modular
insert will cover the left end of the griddle.
Ensure both parts are in contact to achieve an even
cooking surface.
Battery for electronic ignition (Fig. 3A)
(Attitude 2100 LX model)
The spark ignition system is powered by 1 LR06/AA 1.5V
battery.
Inserting the battery: Unscrew the case cover on the right
inside the grill. Insert an AA battery that you will find in the
product box, with the + side outward and put the cover
back on.
Instastart ignition batteries (Fig. 3B)
®
(Attitude 2100 EX model)
The ignition and lighting system operated with control
knobs (Instastart
®
batteries.
Inserting the batteries: remove the lid of the case on the
left inside the grill by sliding it off. Insert 4 AA batteries,
which you will find in your product box, according to the
polarity indicated on the case. Put the cover back on.
Using the control knob lighting: Put the battery case ON/
OFF switch in the ON position (Fig. 3B), then push and
turn the control knobs counterclockwise. After a quarter
turn, the blue light will turn on and will stay on between the
Max Flow position and Reduced Flow position.
12
, on (or in the place of) the
®
) is powered by four LR06/AA 1.5V