Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
English
1. A cold battery may charge at a slower rate than a
warm battery.
2. The hot/cold delay will be indicated by the green
charging LED
6
remaining OFF.
3. Once the battery has reached an appropriate
temperature, the green charging LED
illuminate, indicating that the tool has resumed the
charging procedure.
Electronic Protection System
Li-Ion tools are designed with an Electronic Protection
System that will protect the battery against overloading,
overheating or deep discharge. The tool will automatically
turn off and the battery will need to be recharged.
Important Charging Notes
1. The tool may become warm to the touch while charging.
This is a normal condition, and does not indicate a
problem. To facilitate the cooling of the tool after use,
avoid placing the tool in a warm environment such as in
a metal shed or an uninsulated trailer.
2. If the tool does not charge properly, take the tool and
charger to your local service center.
3. You may charge a partially used battery whenever you
desire with no adverse effect on the tool.
ASSEMBLY AND ADJUSTMENTS
WARNING: To reduce the risk of serious personal
injury, turn unit off and disconnect it from
power sourceremove the battery pack before
making any adjustments or removing/installing
attachments or accessories. An accidental start‑up
can cause injury.
OPERATION
WARNING: To reduce the risk of serious personal
injury, turn unit off and disconnect it from
power sourceremove the battery pack before
making any adjustments or removing/installing
attachments or accessories. An accidental start‑up
can cause injury.
Trigger Switch/Reversing Button (Fig. A)
1. The drill is turned ON and OFF by pulling and releasing
the trigger switch
1
.
2. A forward/reverse control button
direction of the tool and also serves as a lock off button.
3. To select forward rotation, release the trigger switch and
depress the forward/reverse control button to the left.
4. To select reverse, depress the forward/ reverse control
button the opposite direction.
nOTE: The center position of the control button locks the
tool in the off position. When changing the position of the
control button, be sure the trigger is released.
Keyless Chuck (Fig. A)
WARNING: Make certain the lock‑off button is
engaged to prevent switch actuation before installing
or removing accessories.
6
All manuals and user guides at all-guides.com
6
will continuously
2
determines the
WARNING: Do not attempt to tighten drill bits (or any
other accessory) by gripping the front part of the chuck
and turning the tool on. Damage to the chuck and
personal injury may occur when changing accessories.
To Insert a Drill Bit or Other Accessory
1. Grasp the rear half of the chuck
and use your other hand to rotate the front half
the counterclockwise direction, as viewed from the
chuck end.
2. Insert the bit or other accessory fully into the chuck, and
tighten securely by holding the rear half of the chuck and
rotating the front portion in the clockwise direction as
viewed from the chuck end.
Screw Driving
•
For driving fasteners, the reversing button should be
pushed to the left. Use reverse (button pushed to the
right) for removing fasteners. When moving from forward
to reverse, or vice versa, always release the trigger
switch first.
Drilling
•
Use sharp drill bits only.
•
Support and secure work properly, as instructed in the
Safety Instructions.
•
Use appropriate and required safety equipment, as
instructed in the Safety Instructions.
•
Secure and maintain work area, as instructed in the
Safety Instructions.
•
Run the drill very slowly, using light pressure, until
the hole is started enough to keep the drill bit from
slipping out.
•
Apply pressure in a straight line with the bit. Use enough
pressure to keep the bit biting but not so much as to stall
the motor or deflect the bit.
•
Hold the drill firmly with two hands, one hand on the
handle, and the other gripping the bottom around the
battery area.
•
DO NOT CLICK THE TRIGGER OF A STALLED DRILL OFF
AND ON IN AN ATTEMPT TO START IT. DAMAGE TO THE
DRILL CAN RESULT.
•
Minimize stalling on breakthrough by reducing pressure
and slowly drilling through the last part of the hole.
•
Keep the motor running while pulling the bit out of a
drilled hole. This will help reduce jamming.
Drilling in Wood
•
Holes in wood can be made with the same twist drill bits
used for metal or with spade bits. These bits should be
sharp and should be pulled out frequently when drilling
to clear chips from the flutes.
Drilling in Metal
•
Use a cutting lubricant when drilling metals. The
exceptions are cast iron and brass which should be
drilled dry. The cutting lubricants that work best are
sulfurized cutting oil or lard oil.
8
with one hand
9
in
Publicité
Table des Matières
