Important Safety Instructions - Makita AN923 Manuel D'instructions

Cloueuse pneumatica
Masquer les pouces Voir aussi pour AN923:
Table des Matières

Publicité

Les langues disponibles
  • FR

Les langues disponibles

  • FRANÇAIS, page 11
ENGLISH (Original instructions)
1.
Safety glasses
2.
Face shield
3.
Compressor air output per minute
4.
Nailing frequency (times/min.)
5.
Pneumatic tool oil
6.
Contact arm
7.
Nose adapter
8.
Adjuster
9.
Hook
10. Pusher
11. Pusher lever
SPECIFICATIONS
Model
Air pressure
Nail Iength
Nail capacity
Dimensions (L x H x W)
Min. hose diameter
Net weight
• Due to our continuing programme of research and development, the specifications herein are subject to change without
notice.
• Specifications may differ from country to country.
• Weight according to EPTA-Procedure 01/2003
Symbols
The following show the symbols used for the equipment.
Be sure that you understand their meaning before use.
............... Read instruction manual.
.... Wear safety glasses.
.............. Do not use on scaffoldings, ladders.
IMPORTANT SAFETY
INSTRUCTIONS
WARNING:
WHEN USING THIS TOOL, BASIC SAFETY
PRECAUTIONS SHOULD ALWAYS BE FOLLOWED
TO REDUCE THE RISK OF PERSONAL INJURY,
INCLUDING THE FOLLOWING:
READ ALL INSTRUCTIONS.
• For personal safety and proper operation and
maintenance of the tool, read this instruction manual
before using the tool.
• Always wear safety glasses to protect your eyes from
dust or nail injury.
WARNING: It is an employer's responsibility to
enforce the use of safety eye protection equipment by
the tool operators and by other persons in the
immediate working area.
6
Explanation of general view
12. Depress
13. Return
14. Nail stopper
15. Air socket
16. Air fitting
17. Continuous nailing
18. Trigger lock
19. Lock lever
20. Intermittent nailing
21. Hammer
22. Small rod
AN923
0.44 - 0.83 Mpa (4.4 - 8.3 bar)
64 - 74 pcs.
559 mm x 347 mm x 109 mm
END106-3
ENB067-3
23. Ejection port
24. Driver
25. Pliers
26. Slot
27. Trigger lock
28. Change lever
29. Drain cock
30. Air filter
31. Oiler
32. Pneumatic oil
50 mm - 90 mm
455 mm x 365 mm x 109 mm
8.5 mm
4.0 kg
• For Australia and New Zealand only
Always wear safety glasses and face shield to protect
your eyes from dust or nail injury. The safety glasses
and the face shield should conform with the
requirements of AS/NZS 1336.
WARNING: It is an employer's responsibility to
enforce the use of safety eye protection equipment by
the tool operators and by other persons in the
immediate working area. (Fig. 1)
• Wear hearing protection to protect your ears against
exhaust noise and head protection. Also wear light but
not loose clothing. Sleeves should be buttoned or
rolled up. No necktie should be worn.
• Rushing the job or forcing the tool is dangerous.
Handle the tool carefully. Do not operate when under
the influence of alcohol, drugs or the like.
• General Tool Handling Guidelines:
(1)
Always assume that the tool contains fasteners.
(2)
Do not point the tool toward yourself or anyone
whether it contains fasteners or not.
(3)
Do not activate the tool unless the tool is placed
firmly against the workpiece.
(4)
Respect the tool as a working implement.
(5)
No horseplay.
(6)
Do not hold or carry the tool with a finger on the
trigger.
(7)
Do not load the tool with fasteners when any one
of the operating controls is activated.
(8)
Do not operate the tool with any power source
other than that specified in the tool operating/
safety instructions.
• An improperly functioning tool must not be used.
AN943
60 - 84 pcs.

Publicité

Table des Matières
loading

Ce manuel est également adapté pour:

An943

Table des Matières