DeWalt DWE625 Guide D'utilisation page 10

English
Quick Adjustment Using the Graduation
with Zero Reset Ring
1. Loosen the depth stop quick height adjuster lock
2. Unlock the plunge limiter by pushing the release
lever down.
6
3. Lower the router carriage until the cutter is in contact
with the workpiece.
4. Press the quick release button
5. Adjust the depth stop bar
the turret stop 11 . Then set both the quick zero reset
ring 14 and fine zero reset ring
6. Adjust the depth of cut using the quick height
adjuster 16 and the corresponding graduation. The
adjusted depth of cut is indicated by the pointer
7. Tighten depth stop quick height adjuster lock
Fine Adjustment
When not using a depth template, or if the depth of cut
needs readjustment, it is recommended to use the fine
height adjuster 18 .
1. Adjust the depth of cut as described in Adjusting the
Depth of Cut.
2. Set the fine height adjuster to zero using the fine zero
reset ring 19
3. Rotate the fine height adjuster
position: one turn corresponds to approximately 1 mm
and 1 mark to 0.1 mm.
Fitting a Guide Bush (Fig. H)
Together with a template, guide bushes play a valuable part
in cutting and shaping to a pattern.
• Fit the guide bush 24
screws 25 as shown.
Fitting the Parallel Fence (Fig. I, J)
1. Fit the guide rod 26
2. Slide the parallel fence
3. Tighten the wing bolts
Adjusting the Parallel Fence (Fig. A, I, J)
1. Draw a cutting line on the material.
2. Lower the router carriage until the cutter is in contact
with the workpiece.
3. Push quick release button
using the thumb wheel
4. Position the router on the cutting line.
5. Slide the parallel fence
tighten the wing bolts
6. Adjust the parallel fence using the fine adjustment
knob 29 . The outer cutting edge of the cutter must
coincide with the cutting line.
7. If required, loosen the screws
strips 31 to obtain the desired guiding length.
8
7 .
12 until it makes contact with
19 to the zero position.
18 to the required
to the router base 10 using the
to the router base 10 .
27 over the rods.
28 temporarily.
7 and limit the carriage return
4 .
27 against the workpiece and
28 .
30 and adjust the
Connecting Dust Extraction Adaptor (Fig. K)

CAUTION: In normal plunge mode, ensure the base
15 .
of the knurled nut is aligned correctly with the forks of
the lower motor housing. This will enable the cutter to
retract into the base safely.

WARNING: Whenever possible use the hose guide with
a suitable extractor when routing.
The dust extraction adaptor consists of a main section
cover 33
tube screw
1. Slide the cover
clicks into place.
2. Place the main section
17 .
two screws
15 .
3. Remove screw
this screw to assemble the extraction tube adaptor
to the router.
Connecting Dust Extractor Hose (Fig. P)

WARNING: Risk of dust inhalation. To reduce the risk of
personal injury, ALWAYS wear an approved dust mask.
A dust extraction tube adaptor
Vacuum hoses on most vacuum extractors will fit directly into
the dust extraction spout.

WARNING: ALWAYS use a vacuum extractor designed
in compliance with the applicable directives regarding
dust emission when sawing wood. Vacuum hoses of
most common vacuum cleaners will fit directly into the
dust extraction outlet.
1. Connect a dust extractor hose
adaptor
nOTE: When using dust extraction, be sure that the vacuum
cleaner is out of the way and secure so that it will not tip over
or interfere with the router or workpiece. The vacuum hose
and power cord must also be positioned so that they do not
interfere with the router or workpiece. If the vacuum cleaner
or vacuum hose cannot be positioned properly, it should
be removed.
OPERATION

WARNING: To reduce the risk of serious personal
injury, turn unit off and disconnect it from
power source before making any adjustments or
removing/installing attachments or accessories.
An accidental start‑up can cause injury.

CAUTION: Before connecting tool to power
source, check to see that the switch is in the "OFF"
position. An accidental start‑up can cause injury.
Proper Hand Position (Fig. O)

WARNING: To reduce the risk of serious personal injury,
ALWAYS use proper hand position as shown.

WARNING: To reduce the risk of serious personal
injury, ALWAYS hold securely in anticipation of a
sudden reaction.
Proper hand position requires both hands on the main
handles 2
, an extraction tube adaptor
37 , two base screws 42
33 onto the main section
32 on the base and secure with
42 and nuts 36 .
37 from the top of the router and use
34
34 using the D WALT quick lock system.
e
.
32 , a
34 , one extraction
and two nuts 36 .
32 until it
34
is supplied with your tool.
43 to the extraction tube