Aritech ACL599 Manuel De Programmation page 4

GB GB GB
GB GB
P P P P P
ROGRAMMING A A A A A ROGRAMMING ROGRAMMING ROGRAMMING ROGRAMMING
P P P P P
ROGRAM ROGRAM MODE ROGRAM ROGRAM ROGRAM MODE MODE MODE MODE
1. 1. 1. 1. 1. Enter the Engineering code.
Press the "#" button.
2. 2. 2. 2. 2. Type "0".
3. 3. 3. 3. 3. Enter a user number, which
must be a two-digit number
between 01 and 99 (for
example, user code 2 is
"02").
Then enter the PIN code,
which must be between 1
and 8 digits. For example,
PIN code 9874.
4. 4. 4. 4. 4. Press the " " button.
5. 5. 5. 5. 5. To program the next PIN
code, repeat steps 2 to 4.
6. 6. 6. 6. 6. To leave the program, press
the "#" button.
Example Example Example Example Example of programming a user code in memory position 01
and user code 9874:
Type: "Engineering code" # 0 01 9874
P P P P P
ROGRAMMING ROGRAMMING ROGRAMMING ROGRAMMING ROGRAMMING A A A A A CARD
P P P P P
ROGRAM ROGRAM MODE ROGRAM MODE MODE MODE
ROGRAM ROGRAM MODE
1. 1. 1. 1. 1. Enter the Engineering code.
Press the "#" button.
2. 2. 2. 2. 2. Type "0".
3. 3. 3. 3. 3. Enter a user number, which
must be a two-digit number
between 01 and 99 (for
example, user code 2 is
"02").
4. 4. 4. 4. 4. Hold an ACT700 card or an
ACT730 keyfob in front of
the slave reader ACL700.
5. 5. 5. 5. 5. To program the next card or
keyfob, repeat steps 2 to 4.
6. 6. 6. 6. 6. To leave the program, press
the "#" button.
Example of programming a card or a keyfob in memory Example Example
Example Example
position 01:
Type: "Engineering code" # 0 01 hold keyfob in front of
reader #
4
PIN PIN PIN
PIN PIN
CODE CODE CODE CODE CODE
The yellow LED lights up and a long
beep sounds.
A short beep sounds.
A short beep sounds after every
keystroke.
Two short beeps sound to confirm
that the user code has been
accepted.
A short beep sounds and the yellow
LED goes out.
#
CARD CARD CARD OR CARD OR OR OR OR KEYFOB KEYFOB KEYFOB KEYFOB KEYFOB
The yellow LED lights up and a long
beep sounds.
A short beep sounds.
A short beep sounds after every
keystroke.
Two short beeps sound on the
keypad and on the reader. The card
or keyfob is accepted.
A short beep sounds and the yellow
LED goes out.
Attention: Attention: Attention: Attention: Attention: Several beeps indicate that you have done the wrong
keystrokes or actions.
P P P P P
ROGRAMMING ROGRAMMING ROGRAMMING ROGRAMMING ROGRAMMING RELA
Both relays can be programmed in pulse or On/Off mode (the mode is
related to the relay and not per user.) One or two relays can be
assigned to every user code, card or keyfob.
A A A A A
SSIGNING SSIGNING SSIGNING ONE ONE OR ONE ONE OR OR TWO OR TWO RELA TWO TWO RELA RELAYS RELA
SSIGNING SSIGNING ONE OR TWO RELA
1. 1. 1. 1. 1. Enter the Engineering code.
Press the "#" button.
2. 2. 2. 2. 2. Type "3".
3. 3. 3. 3. 3. Enter the user number,
which must be a two-digit
number between 01 and 99
(for example, user code 2 is
"02").
4. 4. 4. 4. 4. Assign the relay or relays to
the user code or card.
Press "1" if relay output
1 needs to be active.
Press "2" if relay output
2 needs to be active.
Press "12" if both relay
outputs 1 and 2 should
be active.
5. 5. 5. 5. 5. Press the " " button.
6. 6. 6. 6. 6. Continue programming the
relay mode or leave the #"
button.
Example : Example : Example : Memory 01 position to be assigned to relay 2
Example : Example :
Type: "Engineering code" # 3 01 2
R R R R R
ELA ELA ELA ELA ELAY Y Y Y Y MODE MODE MODE MODE MODE
Before programming a relay mode, you must have carried out the
procedure above, Assign Pulse, or latching function to relay 1 and/or
relay 2.
7. 7. 7. 7. 7. Assign the relay action,
Pulse or latching.
Press "1" for relay
output 1.
Press "2" for relay
output 2.
Press "00" for latching
(On/Off) function.
Press between 01 and
99 for a pulse function.
(e.g. 05 equals 5
seconds pulse).
8. 8. 8. 8. 8. Press the " " button.
9. 9. 9. 9. 9. To leave the program, press
the "#" button.
Example : Example : Relay 2 with pulse function of 5 seconds Example : Example : Example :
Type: "Engineering code" # 2 05
RELAY Y Y Y Y ACTIONS RELA RELA RELA ACTIONS ACTIONS ACTIONS ACTIONS
/ / / / /
YS YS YS USER USER USER
YS USER USER
The yellow LED lights up and a long
beep sounds.
A short beep sounds.
A short beep sounds after every
keystroke.
A short beep sounds after every
keystroke.
Two short beeps sound.
A short beep sounds and the yellow
LED goes out.
#
A short beep sounds after every
keystroke.
Two short beeps sound.
A short beep sounds and the yellow
LED goes out.
#