Télécharger Imprimer la page

Publicité

Les langues disponibles

Les langues disponibles

Liens rapides

Model #
582Wd
Palmer Nightstand
Assembly Instructions
Congratulations!
This fine piece of furniture will make a gorgeous addition to
your home. For the best results, read the Assembly
Instructions and Finishing Hints before you begin your
project.
Service Policy: We will replace any part that is defective,
missing or damaged during assembly. For a replacement
part, directly contact Whittier Wood Products customer
service department by phone, fax, mail or email.
Hours: Our friendly customer service staff can be reached
Monday-Friday 7:00 a.m. to 5:00 p.m. (Pacific Time). You
may leave a message 24 hours a day, seven days a week.
800-653-3336 • Outside the U.S. or Canada: 541-687-0213 • Fax: 541-687-2060
CALL US FIRST! Do not return this item to the store
www.whittierwood.com • P.O. Box 2827 • Eugene, Oregon 97402, U.S.A.
P.O. Box 2827
Eugene, OR 97402 USA
IMPORTANT NOTES:
For normal household use only. Not recommended for commercial use.
Do not climb, sit or stand on this piece of furniture.
Do not overload drawers on this unit.
Unload items before you move this unit.
Before you load or move this unit, tighten all screws and supports.
Before you begin your project, completely read the Assembly
Instructions and Finishing Hints.
Store this item: 1- in its box; 2- in a dry place; 3- in temperatures that
range from 40°F to 90°F (not on a cold and possibly damp cement
floor).
Periodically inspect your furniture for any loose glue joints, screws or
any other problem that might affect the stability of your furniture.
Tighten or repair as needed.
Notice to California Customers
California Prop 65 requires consumer goods to be labeled if any one of
850+ different chemicals or substances, including wood dust, is present
even in trace amounts. Drilling, sawing, sanding or machining wood
products generates wood dust, a substance known to the State of
California to cause cancer. Warning: This product contains a chemical
or substance known to the State of California to cause cancer, birth
defects or other reproductive harm.
California Health and Safety Code Section 25249.6
DESIGN SUBJECT TO CHANGE WITHOUT NOTICE.
To Order: Provide the furniture model number (upper
portion of this page), the part letter, production code,
quantity needed, reason for replacement and your full
name, address and telephone number.
Parts ship from our Eugene, Oregon factory within one or
two business days from the time we receive your request.
Please allow five to ten business days for delivery.
Production Code:
WARNING
03/14

Publicité

loading

Sommaire des Matières pour Whittier Wood Furniture 582Wd

  • Page 1 Model # 582Wd IMPORTANT NOTES: Palmer Nightstand For normal household use only. Not recommended for commercial use. Do not climb, sit or stand on this piece of furniture. Do not overload drawers on this unit. Assembly Instructions Unload items before you move this unit.
  • Page 2 582Wd Palmer Nightstand — Parts List Please identify the parts and check that quantities received match those on this list. If you need to replace a part, refer to the following letter and model name. Part Description Quantity Small Drawer End...
  • Page 3 582Wd Palmer Nightstand — Parts List continued Please identify the parts and check that quantities received match those on this list. If you need to replace a part, refer to the following letter and model name. Part Description Quantity Drawer Slide...
  • Page 4 Hammer Tack Glides (V) into the bottoms of both sides about one inch from the front and back edges. See Figure 1a. Insert a Cam Connector (Q) into each of the four holes in the underside of the Top (N). See Figure 1b. Page 4 — 582Wd — 03/14...
  • Page 5 Slide the Top (N) down so that the four Cam Connectors (Q) fit into the four holes in the top of the Sides. Insert the Cam Housings (R) and tighten securely. Insert three #8 x 1-1/4" Black Screws (T) through the holes in the sleeper into the top and fasten securely. See Figure 3. Page 5 — 582Wd — 03/14...
  • Page 6 Square the drawers by measuring from the left front to right rear corners and from the right front to left rear corners. The measurements should be equal. If one is longer, hold the drawer by the corners on the longest line and squeeze them together until square. See Figure 5b. Page 6 — 582Wd — 03/14...
  • Page 7 Machine Screw (ZF) through the center hole in the Drawer False Front and LOOSELY fasten the Knob (Wc). See Figure 7. DO NOT insert the LoProfile Screws (Xd) yet. Repeat the above steps for the Large Drawers and the Large Drawer Faces (F). Page 7 — 582Wd — 03/14...
  • Page 8 Drawer False Front (J) and fasten securely. See Figure 8b. Working your way up, repeat the above steps with each drawer. There should be a 1/8" gap between each drawer for the drawer slides to properly function. Page 8 — 582Wd — 03/14...
  • Page 9 Modelo # 582Wd Cómoda de NOTAS IMPORTANTES: Para uso de viviendas normales únicamente. No se recomienda para Noche Palmer uso comercial. Ne se suba, no se siente ni se pare sobre este mueble. No mueva este mueble mientras esté lleno. Vacíelo antes de moverlo.
  • Page 10 Inserte un conector de leva (Q) en cada uno de los cuatro Funcionamiento del Sistema Conector-Leva. orifi cios de la parte inferior de la parte superior (N) de la mesita de noche. Vea la Figura 1b. PAGE 2 SP – 582Wd – 03/14...
  • Page 11 Philtruss #6 x 5/8" (ZD) a través de los orifi cios de la cubierta posterior y atorníllelos bien. Vea la Figura 4. 5. Monte las piezas laterales (B) del cajón pequeño a la pieza delantera falsa del cajón pequeño (C), utilizando dos PAGE 3 SP – 582Wd – 03/14...
  • Page 12 No. De Modèle 582Wd REMARQUES IMPORTANTES : Table de Nuit Pour un usage domestique uniquement. Non recommandé pour un usage commercial. Ne pas monter, s’asseoir ni se mettre debout sur cet article d’ameublement. Ne pas déplacer cet article d’ameublement s’il est chargé.
  • Page 13 Répétez la procédure pour le côté droit (Lb) avec « CR » pour le côté droit de l’armoire, d’un « DR » les glissières de tiroirs (côté droit du meuble) (Z1). pour le tiroir droit. PAGE 2 FR – 582Wd – 03/14...
  • Page 14 à l’aide des vis Philtruss nº 6 x 5/8 po (ZD) que vous introduisez dans les trous préforés à l’arrière. Voir la Figure 4. PAGE 3 FR – 582Wd – 03/14...
  • Page 15 Cam-Lock System INSTRUCTIONS Optimum NOTE: To avoid scratching the surface of the Face of tightness wood, assemble the unit and place face-down Cam Housing on a clean, protected surface. Cam Connector Correct way to tighten your Cam-Lock system. Shoulder must be flush with the surface of the wood.
  • Page 17 Whittier Finishing Hints instructions call for a slow drying glue. Carefully read the Checklist of materials label and instructions of the glue manufacturer. Your unit □ □ □ Rubber gloves Tack cloth #220 & #320 may not need glue. □ □...
  • Page 18 Whittier Finishing Hints Preparing the surface apply additional coats. Lightly sand and wipe surface with a lint-free rag or tack cloth between coats. 1. Sand each piece with #220 grit sandpaper. Sand with the grain of the wood on flat surfaces and opposite the 4.
  • Page 19 Consejos de Whittier para terminaciones Consejos de pegado Lista de control de materiales Estos son algunos consejos generales. Consulte las □ □ □ Guantes de Paño de Papel de lija instrucciones de ensamblaje para obtener información detallada hule adherencia No. 220 y No. sobre cómo pegar el producto específico que utilice.
  • Page 20 Consejos de Whittier para terminaciones Consejos para las terminaciones Aplicación de la capa de acabado Utilice productos de la misma marca para garantizar la Siempre debe leer y seguir las instrucciones de la etiqueta. compatibilidad. No se recomienda mezclar terminaciones a Mezcle suavemente el preparado para la capa de acabado, base de solventes y a base de agua.
  • Page 21 Conseils de finition de Whittier Conseils en matière de collage Liste de vérification des matériaux Cette section contient des conseils d'ordre général. Veuillez vous □ □ □ Gants en Chiffon résiné Papier de reporter aux instructions d'assemblage pour des renseignements □...
  • Page 22 Conseils de finition de Whittier enduits de finition à base de solvant et d'eau. Lisez et suivez Lisez et suivez les instructions figurant sur l'étiquette. toujours les instructions figurant sur le produit. Mélangez doucement l'enduit de finition; n'agitez pas. Le fait d'agiter peut entraîner la formation de bulles qui seront par la L'aulne est un bois dur et poreux dont l'aspect est souvent suite difficiles à...