Publicité
Liens rapides
Model #
901Wc
Seneca Telephone Stand
Assembly Instructions
Congratulations!
This fine piece of furniture will make a gorgeous
addition to your home. For the best results, read the
Assembly Instructions and Finishing Hints before
you begin your project.
CALL US FIRST!
Service Policy: We will replace any part that is
defective, missing or damaged during assembly.
Please contact Whittier Wood Products customer
service department directly by phone, fax, mail or
email for a replacement part.
Hours: Our friendly customer service staff can be
reached Monday-Friday 7:00 a.m. to 5:00 p.m. (Pacific
Time). You may leave a message 24 hours a day,
seven days a week.
800-653-3336
www.whittierwood.com • P.O. Box 2827 • Eugene, Oregon 97402, U.S.A.
• Outside the U.S. or Canada: 541-687-0213 • Fax: 541-687-2060
P.O. Box 2827
Eugene, OR 97402 USA
IMPORTANT NOTES:
For normal household use only. Not recommended
for commercial use.
Do not climb, sit or stand on this piece of furniture.
Do not overload the shelves or drawers.
Unload items before you move this unit.
Before you begin your project, completely read the
Assembly Instructions and Finishing Hints.
Store this item: 1- in its box; 2- in a dry place; 3- in
temperatures that range from 40°F to 90°F (not on a
cold and possibly damp cement floor).
Periodically inspect your furniture for any loose
glue joints, screws or any other problem that might
affect the stability of your furniture. Tighten or
repair as needed.
Do not return this item to the store.
To Order: Provide the furniture model number (upper
left corner of this page), the part letter, production
code, quantity needed, reason for replacement, your
full name, address and telephone number.
Parts ship from our Eugene, Oregon factory within one
or two business days from the time we receive your
request. Please allow five to ten business days for delivery.
Production Code:
VN
.
06/10
Publicité
Manuels Connexes pour Whittier Wood Furniture Seneca 901Wc
Sommaire des Matières pour Whittier Wood Furniture Seneca 901Wc
- Page 1 Model # 901Wc Seneca Telephone Stand Assembly Instructions IMPORTANT NOTES: For normal household use only. Not recommended for commercial use. Do not climb, sit or stand on this piece of furniture. Do not overload the shelves or drawers. Unload items before you move this unit. Before you begin your project, completely read the Assembly Instructions and Finishing Hints.
- Page 2 901Wc Seneca Telephone Stand — Parts List Please identify the parts and check that quantities received match what is on this list. If you need to replace a part, refer to the following letter and item name. 2-3/8" Qty. 1 Back Qty.
- Page 3 Assembly Instructions Tools Required: Phillips Screwdriver, Mallet or Padded Hammer, Wood Glue Fig. 1 The backs of the Left and Right Side Assemblies are grooved. Spread a thin layer of glue in the dowel holes in the Left Side Assembly (Rb). Making sure the curved edge of the front stretcher faces the front of the unit and all pocket drilled holes face down, insert the Front Stretcher (J), Back Stretcher (K), and Shelves (L) into the Left Side Assembly (Rb).
- Page 4 Fig. 3a Fig. 3 Apply a light film of glue in the two dowel holes at each side on the bottom of the Top (H) and slide the Top down over the dowels in the top edges of the Sides (Qb and Rb). Using the pocket drilled holes as guides, fasten in place with #8x1-3/16"...
- Page 5 Fig. 5a Fig. 5 Slide the Drawer Bottom (M) into the grooves in the sides and front. See Figures 5 and 5a. Fig. 6a Fig. 6 Attach the Drawer End (O) to the Drawer Sides (Pb) with #8x1-3/16" Pan Head Screws (S). See Figures 6 and 6a.
- Page 6 x 10 Fig. 7 Attach the Back (Ic) with #6 x 5/8" Philtruss Screws (T) through predrilled holes. See Figure 7. Fig. 8 Insert the upper drawer half way into the unit and insert two Dowels (D) into the holes near the front edge of the top.
- Page 7 Fig. 9 Turn the unit upside down on a clean, protected surface and insert the bottom drawer. See Figure 9. Fig. 10 Center and align the Drawer Stop (G) to the bottom edge of the Front Stretcher and attach with two #6 x 5/8" Philtruss Screws (T). See Figure 10. Turn your unit upright. Page 7 —...
- Page 8 Modelo # 901Wc Messita para Teléfono Seneca Instrucciones de ensamblaje NOTAS IMPORTANTES: Sólo para uso doméstico. NO se recomienda para uso comercial. Ne se suba, no se siente ni se pare sobre este mueble. No mueva este mueble mientras esté lleno. Vacíelo antes de moverlo.
- Page 9 901Wc Mesita para teléfono Seneca Lista de piezas Identifique las piezas y verifique que las cantidades que recibió coincidan con las de la lista. Si necesita reemplazar una pieza remítase a la siguiente letra y nombre de la misma. Parte Descripción Cantidad Parte...
- Page 10 Añada la parte posterior (Ic) con tornillos Philtruss #6 x 5/8" Glue all dowels this step = Una con pegamento los (T) en los huecos pre-taladrados. Ver Figura 7. taquetes durante este paso. Aplique una capa fina de pegamento en los dos huecos para los taquetes en la cara oculta de la parte superior Inserte el cajón superior hasta la mitad en la unidad e inserte (H).
- Page 11 No. de Modèle 901Wc Meuble à Téléphone Seneca Instructions d’assemblage REMARQUES IMPORTANTE: Pour usage ménanger normal seulement. N’est pas recommandé pour usage commercial. Ne pas monter, s’asseoir ni se mettre debout sur cet article d’ameublement. Ne pas déplacer cet article d’ameublement s’il est chargé. Le décharger avant de le déplacer.
- Page 12 901Wc Meuble à téléphone Seneca Liste des pièces Veuillez identifier les pièces et vérifier que les quantités reçues correspondent à la quantité indiquée sur la liste. S’il faut remplacer une pièce, consulter la lettre qui figure ci-dessous et le nom de l’article. Pièce Description Qté...
- Page 13 Glue all dowels this step = Collez toutes les goupilles Fixez le dos (Ic) avec les vis Philtruss no 6 x 5/8 po (T) à cette étape. dans les orifices pré-perforés. Voir Figure 7. Appliquez un léger film de colle dans les deux trous de goupille dans le côté...
- Page 14 1. Choose a finish that will meet your expectations for the product you are finishing. Are you matching existing furniture or do you want a “natural” finish? Is the piece to be functional, decorative or both? The answers Rubber gloves to these questions may affect the type of finish you choose.
- Page 15 Gluing Hints (cont.) 3. We recommend that you use a good wood glue, such as Elmer’s Wood Glue or White Glue, Tite- bond Wood Glue or the equivalent; unless the instructions call for a special type such as a slow drying epoxy glue.