Télécharger Imprimer la page

Denon DBP-4010UDCI Manuel De L'utilisateur page 10

Publicité

Les langues disponibles

Les langues disponibles

ENGLISH
About the Remote Control Unit
Inserting the Batteries
q· Remove· the· remote· control·
w· Set· three· R6/AA· batteries· in·
unit's·rear·cover.
e· Put·the·rear·cover·back·on.
NOTE
Use·R6/AA·batteries·in·this·remote·control.·
Replace· the· batteries· with· new· ones· if· the· set· does· not· operate·
even· when· the· remote· control· unit· is· operated· close· to· the· unit.·
(The·supplied·batteries·are·only·for·verifying·operation.)
When·inserting·the·batteries,·be·sure·to·do·so·in·the·proper·direction,·
following·the·"q"·and·"w"·marks·in·the·battery·compartment.
To prevent damage or leakage of battery fluid:
Do·not·use·a·new·battery·together·with·an·old·one.
Do·not·use·two·different·types·of·batteries.
Do·not·attempt·to·charge·dry·batteries.
Do·not·short-circuit,·disassemble,·heat·or·dispose·of·batteries·in·
flames.
If the battery fluid should leak, carefully wipe the fluid off the inside
of·the·battery·compartment·and·insert·new·batteries.
Remove·the·batteries·from·the·remote·control·unit·if·it·will·not·be·in·
use·for·long·periods.
Used·batteries·should·be·disposed·of·in·accordance·with·the·local·
regulations·regarding·battery·disposal.·

Operating Range of the Remote Control
Unit
the·battery·compartment·in·the·
Point·the·remote·control·unit·at·the·remote·sensor·when·operating·
indicated·direction.
it.
NOTE
The·set·may·function·improperly·or·the·remote·control·unit·may·not·
operate· if· the· remote· control· sensor· is· exposed· to· direct· sunlight,·
strong artificial light from an inverter type fluorescent lamp or infrared
light.
30°
30°
Approx.23feet/7m
Remote Control Settings (Remote
Control Side)
Switches when the DBP-4010UDCI's remote control operates
another DENON BD players in the vicinity.
Set·the·remote·control·code·simultaneously·on·the·main·unit,·too.·
For· how· to· set· codes,· see· GUI· menu:· "Other· Setup"· –· "Remote·
Control·Setting"·–·"Remote·ID"·(vpage·31).
GRemote control code settingH
:·Set·the·remote·control·code·to·"1".
1
:·Set·the·remote·control·code·to·"2".
2
If·the·signal·code·of·the·remote·control·does·not·match·the·signal·
code·of·the·unit,·the·remote·control·code·set·on·the·unit·is·shown·
on·the·display.·
GExampleH
If·the·code·setting·on·the·unit·is·"DENON·1",·and·the·setting·on·the·
remote·control·is·"2",·"PLAYER·1"·is·shown·on·the·display.·
NOTE
Match·the·signal·code·of·the·remote·control·with·the·signal·code·of·
the·unit.·If·the·remote·control·code·is·different,·you·cannot·operate·
the·DBP-4010UDCI·with·the·remote·control.·
Even·if·you·change·the·remote·control·code,·set·GUI·menu·"Other·
Setup"· –· "Remote· Control· setting"· –· "Receive· Legacy· Remocon"·
(vpage· 31)· to· "Off"· when· operating· the· DBP-4010UDCI· with· a·
remote·control·other·than·DENON's.

Publicité

loading