Auto Setup; Quick Guide For Menu Operation - JVC LT-19HA22U Mode D'emploi

Auto setup

The built-in tuner allows to receive TV-channels
from analog cable-tv or DVB-T. If, however, you are
receiving TV-channels via separate receiver, no need
to run the TV's auto-tuning. Just set your language
here and then jump to next chapter.
When initially operating the TV after purchase, the
menu: 'Auto Installation' will appear automatically by
default. Do start 'Auto Installation' by connect DVB-T
antenna-cable, if available. Wait for the TV to save all
digital TV-channels. When finished, disconnect digital
cable-tv. Now connecting analog cable-tv, if available.
Re-run auto-tuning for analog tv-channels (see page
12, update scan).
Note: If analog cable-tv is not available (or you
discontinued using), do connect a DVB-T-antenna (not
supplied) and start auto-tuning for DVB-T-channels.
Preparation:
Press (Power) on the unit or press
the remote.
1
Auto Installation menu will appear.
Press or to select desired language.
Then press
.
Auto Installation
Please select your language Deutsch
then press "ENTER" English
2 Français
on your remote control:
Press or to select your country.
Then press
.
Auto Installation
Please select your country Germany
UK
then press "ENTER"
3 France
on your remote control:
Press or to select Home.
Then press
.
Auto Installation
Please select where the TV will be Home
placed.
Store
The picture will be optimized for
4
that location.
If you cancel Auto Power Off (see page 20),
press or to select Off. Then press
Auto Installation Auto Power Off
Your TV has been set to power off
On
after 4 hours of continuous viewing.
Off
If you want to change this setting,
please choose Off.
This setting can also be changed in
the MENU.
5
TV will search for Digital TV-channels at first.
Connect your DVB-T antenna now.
Continue with ENTER to start auto tuning.
The tuning's progress will be displayed in
percent for confirmation.
Auto Installation
TV will search for Digital CH, Scan
please connect aerial(RF) lead.
Press [ENTER] to start.
If you skip this step,
it can be installed at a later stage
in the MENU.
0%
Note:
• Please be patient - the Auto Tuning process
can take several minutes to complete.
6
When the tuning for Digital TV-channels is
completed, you will be asked if you want
to proceed to autotuning for Analog TV-
channels. If you wish to start autotune Analog
TV-channels, connect your Analog cable-TV
antenna and press ENTER.
(On/Standby) on
Language
Country
TV Location
.
Channel Scan
Note:
• If you do not wish to carry out the autotuning for
Analog TV-channels, press RETURN to exit the menu.
Auto Installation
TV will search for Analogue CH,
Scan
please connect aerial(RF) lead.
Press [ENTER] to start.
If you skip this step,
it can be installed at a later stage
in the MENU.
7
100%
When the display reads 100%, press ENTER
to finish.
Note:
• To cancel the auto tuning, press RETURN during the
process.
THE AUTOMATIC TUNING PROCESS WILL
ONLY START BY ITSELF THE FIRST TIME YOU
SWITCH THE SET ON. HOWEVER YOU CAN
RESTART THIS PROCESS VIA THE MENU
SYSTEM (see page 12).
It is important to enter "Deutsch" in Step 1 and
"Deutschland" in Step 2 for correct operation of
the appliance in Germany.
• If you could not set up a correct pair of language and
country in this auto setup process, you will be able to
make your preferred language selection as illustrated in
page 12 (On-screen Language Selection).

Quick guide for Menu operation

Make sure the antenna connection and power
supply are connected as per the description on
previous page.
Preparations:
• Turn on the unit with the
The (On/Standby) indicator will light up in blue.
Call Menu and for example: Select Auto Scan.
1
Press INPUT SELECT. Select TV. Press MENU.
2
Press or to select
3
Press or to select Channel Set Up, then press .
Picture
Audio
Setup
O i
• If the channel which Channel Block (P.16) was set
exits, password entering screen will appear. Then
enter the password.
4
Press or to select Auto Scan.
Picture
Audio
Setup
... on the following pages the MENU can be
called in the same way as here.
5
Press MENU to exit the menu.
Note:
• If no buttons are pressed for more than approx. 60
seconds, the Menu screen disappears automatically.
Channel Scan
(Power) button on the unit.
then press .
11