KIKKA BOO CRUZ Mode D'emploi page 7

4. ADJUSTING THE HEADREST HEIGHT: 9 headrest height positions
As children are not all the same height, the headrest may be adjusted upwards or downwards. A correctly adjusted headrest ensures optimal protection for the child in the safety
seat. Pull the adjusting ring of the headrest upwards, move the headrest up or down, and release the adjuster to fasten the headrest in the required position. IMPORTANT: After
each adjustment, check if it is properly engaged by sliding the headrest downwards slightly.
5. 360° ROTATION
The car seat can be rotated 360° , in order to help to put your child into or take your child out of car seat.This also allows you change the position of the seat from rearward-facing
to forward-facing.While keeping the rotation button pulled rotate the seat shell,you can rotate the seat shell towards the door and strap the child in without di culty.
WARNING! While travelling the car seat must always be locked in the rearward-facing or forward-facing position.Never use the seat unlocked position while travelling.Make sure
that the seat shell is correctly locked into place by trying to rotate it,you can hear click to insure the shell is locked.
Noted! Avoid getting any dirt or sand in between the upper seat shell and the base: this can have a negative impact on the performance of the rotation and recline
function.Should this happen the dirt should be removed before rotating and reclining the seat any further to avoid any permanent damage of the seat.
6. INSTALL FOR GROUP 0+: ISOFIX+TOP TETHER
For Group 0+(from birth to 18KGS, from birth to 4years), the baby car seat should be installed rearward-facing, using ISOFIX and top tether to t the seat to vehicle seat. And use
the 5-point safety belt to x the child.
Step 1: Pull the rotation button to rotate the car seat shell from forward-facing to rear-facing.and make sure to be locked in rear-facing position.Pull reclining position adjustment
button to adjust the baby car seat shell to the full reclined position. Please check the arrows point to blue marks.
Step 2: Place the child seat rmly against the back of forward-facing vehicle seat.
Step 3: Install ISOFIX system. Release the ISOFIX system and pull out the head locker to the longest position. Connect the ISOFIX connectors to the vehicle ISOFIX attachments till
the indicator turns from red to green and a click is heard. Then push the seat against the vehicle seat back until tight.
ATTENTION:Please check both sides if ISOFIX telescope is on GREEN color. Please push or pull the car seat if the indicator is red color. To remove and uninstall the seat remove the
top tether, then pull the red ISOFIX handle at the front of the seat and pull the seat forward.
Press on the red button on each side of connector to release from the vehicle ISOFIX anchorages.
Step 4: Install the top tether. The top tether is located at the top of the seat back. Extend the length by squeezing the tension indicating adjuster. Locate the vehicle attachment
point which may be found on the parcel shelf, back of the seat or the rear trunk area and hook on. Tighten the tether strap until the adjuster indicator shows green.
Step 5: Place the child in the car seat, making sure that your child's back adheres to the back of the chair. Use a 5-point seat belt to secure the child, and make sure that the seat
belt buckle is properly locked and the shoulder straps are at the correct height for your child.
7. INSTALLING FOR FORWARD-FACING GROUP I: ISOFIX+VEHICLE BELT
For Group I （9-18KGS, 9 months to 4 years old), this child seat should be installed forward-facing, using vehicle belt to t the child seat and 5 point safety belt to x the child.
ATTENTION: ISOFIX system is optional for Group I.
Install ISOFIX system. Release the ISOFIX system and pull out the head locker to the longest position.
Connect the ISOFIX connectors to the vehicle ISOFIX attachments till the indicator turns from red to green and a click is heard. Then push the seat against the vehicle seat back
until tight.
ATTENTION:Please check both sides if ISOFIX telescope is on GREEN color. Please push or pull the car seat if the indicator is red color.
To remove and uninstall the seat remove the top tether, then pull the red ISOFIX handle at the front of the seat and pull the seat forward. Press on the red button on each side of
connector to release from the vehicle ISOFIX anchorages.
Step 1. Pull the rotation button to rotate the car seat shell to forward-facing,and make sure to lock in rear-facing position.Pull reclining position adjustment button to adjust the
baby car seat shell to the middle reclined positions 2 or 3 or 4. Please check the arrows point to red marks on the base of seat.
Step 2: Release the buckle and take out the cushion(for child over 13KGS, there is no need for a cushion). Place the child seat rmly against the back of forward-facing vehicle seat.
Step 3: Pull th lap and the diagonal section of the vehicle seat belt until fully extended, place the diagonal part of vehicle seat belt through the headrest guider while placing
the lap belt through the groove marked red. Put 2 parts(diagonal and the lap) on the back of pad passing one side to the other side.
Step 4: Tighten the vehicle seat belt by pulling rst the lap section then the diagonal part along the direction . Make sure there is no twist in the vehicle belt.
Step 5: Place your child into the child seat,make sure that your child's back is at against the back of child seat.Use 5-point safety belt to x the child,and make sure the safety
harness buckle is correctly locked and the shoulder strap at the right height of your child.
8. INSTALLING FOR GROUP II, III: ISOFIX+VEHICLE BELT
For Group II, III (15-36KGS, 3 years old -12 yeas old), this child seat should be installed forward-facing, using vehicle belt to x the child and the child seat.
Attention: ISOFIX system is optional for Group II,III.
Step 1: Before tting the seat, release the buckle and remove 5-point safety belt(the shoulder straps,crotch strap and lap strap,remove buckle by removing the metal under the
cover.
Step2: Press the rotation button to rotate the car seat shell to forward-facing,and make sure to lock in rear-facing position.Pull reclining position adjustment handle to adjust the
baby car seat shell to the reclined position 1. Please check the arrows point to red marks on the base of seat.
Step 3:Place the child seat rmly against the back of forward-facing vehicle seat.
Step 4: Place your child in the child seat,make sure that your child's back is at against the back of child seat.Pull out of the 3 point vehicle seat belt and place the diagonal belt
goes through the backrest guider while lap belt through the groove marked red.Make sure both diagonal and lap parts go through the groove marked red on the other side
before fasten the vehicle belt.
9. CLEANING AND MAINTENANCE
These instructions are important. Read them carefully and keep for future reference.
Remove the harness system. Remove the seat cover. To replace the cover, keep the product.
IMPORTANT: The seat cover is a safety feature. Do not use the safety seat without its cover. Do not put the child' s safety at risk by using a di erent replacement cover that has not
been approved, as this would reduce the level of protection o ered by the seat.
CARE INSTRUCTIONS: The cover is removable and washable at 30 °C. Line dry only. Machine wash, cold. Do not bleach. Do not iron. Dryclean, any solvent except Trichlorethylene.
Do not tumble dry. If in doubt, consult either the child restraint system manufacturer or the retailer.
ENGLISH