Nice Wingo 4024 Instructions Et Avertissements Pour L'installation Et L'utilisation page 6

Durability of the product
Durability is the average economic life of the product. The value of durability is
strongly influenced by the demand index of the manoeuvres performed by the
automatism: that is the sum of all the factors which contribute to the wear of
the product (see Table 2).
To establish the probable durability of your automatism proceed as follows:
01. Calculate the demand index summing the values in percentage of the
entries present in Table 2 to each other;
02. In Graph A, from the value just found, trace a vertical line until you intersect
the curve; from this point trace a horizontal line to cross the line of "cycles of
manoeuvres". The value established is the estimated durability of your product.
The estimate of durability is performed on the basis of the design calculations
and the results of tests carried out on prototypes. In fact, being an estimate, it
does not give any guarantee on the actual duration of the product.
TABLE 2
> 100 Kg
> 200 Kg
Leaf weight:
> 300 Kg
> 400 Kg
1 - 2 m
Leaf length: 2 - 3 m
3 - 3,5 m
Operating temperature:
Blind leaf:
Installation in windy area:
Note - The content of the present declaration corresponds to the latest available revision, before the printing of the present manual, of the document registered at the head
offices of Nice S.p.a. The present text has been readapted for publishing reasons.
Number: 143/WINGO
The undersigned Lauro Buoro, managing director, declares under his sole responsibility that the following product:
Manufacturer's name: NICE s.p.a.
Address: Via Pezza Alta 13, Z.I. Rustignè, 31046 Oderzo (TV) Italy
Type: Electromechanical operator "WINGO" for swing gates
Models: WG4000, WG4000/V1, WG5000, WG5000/V1, WG4024, WG5024
Accessory: No accessory
conforms with the requirements of the following EC directives:
• 98/37/EC (89/392/EEC amended); DIRECTIVE 98/37/EC OF THE EUROPEAN PARLIAMENT AND COUNCIL of 22 June 1998 regarding the approxima-
tion of member state legislation relating to machinery
As established in directive 98/37/EC, the above-mentioned product may not be started up unless the machine in which the product is incorporated has
been identified and declared as conforming to directive 98/37/EC.
Satisfies the essential requirements of the following Directives, as amended by the directive 93/68/EEC of the European Council of 22nd July 1993:
• 2006/95/EEC (ex directive 73/23/EEC); DIRECTIVE 2006/95/EEC OF THE EUROPEAN PARLIAMENT AND COUNCIL of 12 December 2006 regarding
the approximation of member state legislation relating to electrical material intended for use within specific voltage limits
According to the following harmonised standards:
EN 60335-1:1994+A11:1995+A1:1996+A12:1996+A13:1998+A14:1998+A15:2000+A2:2000+A16:2001
• 2004/108/EEC (ex directive 89/336/EEC); DIRECTIVE 2004/108/EEC OF THE EUROPEAN PARLIAMENT AND COUNCIL of 15 December 2004 regard-
ing the approximation of member state legislation relating to electromagnetic compatibility, repealing directive 89/336/EEC
According to the following harmonised standards: EN 61000-6-2:2005; EN 61000-6-3:2001+A11:2004
The product also complies with the applicable parts of the following standards:
EN 60335-1:2002+A1:2004+A11:2004+A12:2006+ A2:2006, EN 60335-2-103:2003, EN 13241-1:2003; EN 12453:2002; EN 12445:2002;
EN 12978:2003
Oderzo, 24 November 2008
4 – English
Demand index
WG4024 WG5024
WG4000 WG5000
WG4000/V1 WG5000/V1
10 % 0 %
20 % 10 %
30 % 20 %
- 30 %
20 % 0 %
- 10 %
- 20 %
20 % 20 %
15 % 15 %
15 % 15 %
CE DECLARATION OF CONFORMITY
GRAPH A
125.000
100.000
75.000
50.000
25.000
0
0 10
Example of calculation of durability of a Wingo WG5024 gear motor (refer
to Table 2 and Graph A):
- leaf weight = 200 Kg (demand index= 10%)
- leaf length = 2.5 m (demand index = 20%)
- no other stress elements present
Total demand index = 20%
Durability estimate = 80.000 cycles of manoeuvre
Revision: 4
Lauro Buoro (Managing Director)
20 30 40 50 60 70 80 90 100
Demand index (%)