Key Automation SUN Serie Instructions Et Avertissements Pour L'installation Et L'usage page 10

EN
2 - INTRODUCING THE PRODUCT
2.1 - Description of the product
The gear motor SUN is intended to be installed within systems for
the automation of sliding gates. The SUN gear motors have been
designed to automate sliding gates within the weight limits indicated
2.2 - Model and technical characteristics
Code
SUN4024
SUN4224
SUN7024/SUN7024M*
SUN7224
SUN11024/SUN11024M*
SUN52
SUN82
SUN122
* magnetic limit switches
TECHNICAL DATA
MODELS
TECHNICAL SPEC.
Speed cm/s
Torque Nm
Working cycle %
Control unit
Power supply Vac(Vdc)
Absorption
Engine power W
Capacitor µF
Thermoprotection °C
Integrated lights
Degree of protection IP
Dimensions (L-P-H) mm
Weight Kg
Operating temperat. °C
Leaves max weight Kg
3 - PRELIMINARY CHECKS
Before installing this product, verify and check the following steps:
- Check that the gate or door are suitable for automation
- The weight and size of the gate or door must be within the maxi-
mum permissible operating limits
- Check the presence and strength of the security mechanical stops
of the gate or door
- Check that the mounting area of the product is not subject to flood-
ing
- Conditions of high acidity or salinity or proximity to heat sources
could cause malfunction of the product
- Extreme weather conditions (for example the presence of snow,
ice, high temperature range, high temperatures) may increase the
friction and therefore the force required for the handling and initial
starting point may be higher than under normal conditions.
10
Description
24 Vdc gear motor with mechanical limit switches, gate maximum weight 400 kg
24 Vdc gear motor with mechanical limit switches, gate maximum weight 400 Kg
24 Vdc gear motor with mechanical limit switches, gate maximum weight 700 Kg
24 Vdc gear motor with mechanical limit switches, gate maximum weight 700 Kg
24 Vdc gear motor with mechanical limit switches, gate maximum weight 1100 Kg
230 Vac gear motor with mechanical limit switches, gate maximum weight 500 Kg
230 Vac gear motor with mechanical limit switches, gate maximum weight 800 Kg
230 Vac gear motor with mechanical limit switches, gate maximum weight 1200 Kg
SUN4024 SUN4224
21 21
12 12
50 50
14A CT10224
230(24) 230(24)
A 1,1 1,1
250 250
- -
- -
YES -
44 44
330-210-300 330-210-300 330-210-300 330-210-300 330-210-300 330-210-300 330-210-300 330-210-300
12 12
-20+55 -20+55
400 400
in the technical specifications table.
The use of gear motors for applications which differ from those
indicated above is prohibited.
SUN7024/ SUN11024/
SUN7224
SUN7024M SUN11024M
25 25
26 26
80 80
14A CT10224
230(24) 230(24) 230(24)
2,5 2,5
500 500
- -
- -
YES -
44 44
12,5 12,5
-20+55 -20+55
700 700
- Check that the manual operation of gate or door is smooth and
friction-free and there is no risk of derailment of the same
- Check that the gate or door are in equilibrium and stationary if left
in any position
- Check that the power line to supply the product is equipped with
proper grounding safety and protected by a magnetothermal and
differential security device
- Provide the power system with a disconnecting device with a gap
of contacts enabling full disconnection under the conditions dictated
by the overvoltage category III.
- Ensure that all materials used for the installation comply with cur-
rent regulations
SUN52 SUN82
20 16
38 16
80 30
14A CT102B CT102B
230 230
2,3 1,3 1,9
450 300 450
- 12,5
- 150 150
YES -
44 44
13 12
-20+55 -20+55 -20+55
1100 500 800
SUN122
16 16
23 35
30 30
CT102B
230
2,6
600
16 20
150
- -
44 44
13 14
-20+55
1200