Klarfit Ultimate Gym 9000 Mode D'emploi page 47

1. Start with the Upper Cable (67)
(a) With Upper Cable (67) in groove of Pulley (56), thread Upper Cable (67) through Upper Cross Beam (18).
(b) Install Pulley No.1 (56) to Upper Cross Beam (18), using one M10X45mm Hex Bolt (102), two M10 Washers (112) and one
M10 Nylon Nut (117).
(c) Install Pulley No.2 (56) and two Pulley Bushings (small) (89) to Support Frame (6), using one M10X70mm Hex Bolt (100), two
M10 Washers (112) and one M10 Nylon Nut (117).
(d) Install Pulley No.4 (56) to Upper Cross Beam (18), using one M10X45mm Hex Bolt (102), two M10 Washers (112) and one
M10 Nylon Nut (117).
(e) Attach the bolt end of Upper Cable (67) to Selector Shaft (5) with Plastic Washer (71).
(f) Install Pulley No.3 (56) to Pulley U (40), using one M10X45mm Hex Bolt (102), two M10 Washers (112) and one M10 Nylon
Nut (117).
(g) Attach Lat Bar (17) to the other end of Upper Cable (67), using one Pothook (58).
2. Assembly the Butterfly Cable (68)
(a) Attach both ends of Butterfly Cable (68) to Right & Left Butterfly Arm (11&12), using two Plastic Covers (92).
(b) Install Pulley No.5&7 (56) to two Single Pulley Blocks (41), using two M10X45mm Hex Bolts (102), four M10 Washers (112)
and two M10 Nylon Nuts (117).
(c) Install Pulley No.6 (56) to Reverse U (39), using one M10X45mm Hex Bolt (102), two M10 Washers (112) and one M10 Nylon
Nut (117).
3. Assembly the Lower Cable (69)
(a) With the Lower Cable (69) in groove of Pulley (56) through Leg Extension Frame (8).
(b) Install Pulley No.8 (56) and two Pulley Bushings (small) (89) to Leg Extension Frame (8), using one M10X70mm Hex Bolt
(100), two M10 Washers (112) and one M10 Nylon Nut (117).
(c) Install Pulley No.9 (56) and two Pulley Bushings (small) (89) to Support Frame (6), using one M10X70mm Hex Bolt (100), two
M10 Washers (112) and one M10 Nylon Nut (117).
(d) Install Pulley No.10 (56) to Reverse U (39), using one M10X45mm Hex Bolt (102), two M10 Washers (112) and one M10
Nylon Nut (117).
(e) Install Pulley No.11 (56) to Base Frame (1), using one M10X45mm Hex Bolt (102), two M10 Washers (112) and one M10
Nylon Nut (117).
(f) Install Pulley No.12 (56) to Pulley U (40), using one M10X45mm Hex Bolt (102), two M10 Washers (112) and one M10 Nylon
Nut (117).
(g) Install Pulley No.13 (56) to Leg Press Base Frame (2), using one M10X45mm Hex Bolt (102), two M10 Washers (112) and one
M10 Nylon Nut (117).
(h) Install Pulley No.14 (56) and two Pulley Bushings (small) (89) to Leg Press Lower Support Frame (19), using one M10X70mm
Hex Bolt (100), two M10 Washers (112) and one M10 Nylon Nut (117).
(i) Install Pulley No.15 (56) to Rear Leg Press Upright Frame (24), using one M10X45mm Hex Bolt (102), two M10 Washers
(112) and one M10 Nylon Nut (117).
(j) Attach the bolt end of Lower Cable (69) to Leg Press Seat Support Frame (22), using one Pothook (58), one Short Chain (63),
one M8X40mm Hex Bolt (107), two M8 Washers (114) and one M8 Nylon Nut (118).
(k) Attach Low Bar (16) or Ankle Strap (74) to the other end of Lower Cable (69), using one Long Chain (62) and two Pothooks
(58).
EN
47