Monacor SPEECH -204 Mode D'emploi page 10

the distance between the lectern and the micro-
phone, if required .
2 . If reception is poor, turning or moving the lectern
may improve it .
6.1.3 Setting the squelch
The squelch function will mute the respec-
tive receiver section when the level of the
radio signal falls below the threshold value
adjusted . Thus, interference signals will not
cause noise when the transmitter is switched
off or when its radio signal is poor: If the
levels of the interference signals are below
the threshold value, the receiver section will
be muted . A high threshold value offers high
interference resistance, but it will also reduce
the transmission range .
1) Switch off the receiver sections A and B .
Then keep the button SET pressed while
switching on a receiver section . The display
will indicate or
flashing .
2) Press the button SET to activate the
squelch setting mode:
and the current value (flashing) will appear
on the display .
3) Use the button  or  to set the value
(level 7 = highest threshold value) . Press
the button SET to exit the squelch setting
mode .
Note: The setting modes will be automatically exited
after 5 seconds if no button is pressed . Any settings
made will be saved .
6.2 Reading light
To switch on the reading light (2), set the
switch (3) to the position "I" or "II" according
to the brightness level desired .
All rights reserved by MONACOR
manual may be reproduced in any form or by any means for any commercial use.
10
7 Specifications
Amplifier power
RMS power: � � � � � � � � � � � � � � 75 W
Peak power: � � � � � � � � � � � � � � 100 W
Speaker: � � � � � � � � � � � � � � � � � � 2-way system
Frequency range: � � � � � � � � � � � � 60 – 20 000 Hz
Wireless receiver sections: � � � � � 2
Reception range: � � � � � � � � � � � � 30 m approx�
Received frequencies
Channel
, with the number
Input sensitivity
MIC 1, MIC 2
(for "Squelch")
(XLR jacks, top): � � � � � � � � � � � 15 mV
Microphone input of channels 1– 3
(XLR jacks, rear): � � � � � � � � � � � 4 mV
JACK-LINE, 6�3 mm jack: � � � � � 220 mV
AUDIO IN, RCA: � � � � � � � � � � � 250 mV
Pin configuration of the microphone inputs, XLR
Channels 1 and 2:
2
2
Channel 3:
2
Pin configuration of the line inputs, 6�3 mm jack:
Output LINE OUT, REC: � � � � � � � 390 mV
Equalizer
LOW: � � � � � � � � � � � � � � � � � � � ±12 dB at 60 Hz
MID: � � � � � � � � � � � � � � � � � � � � ±7 dB at 1 kHz
HIGH: � � � � � � � � � � � � � � � � � � � ±12 dB at 15 kHz
Power supply: � � � � � � � � � � � � � � 230 V/ 50 Hz
Power consumption: � � � � � � � � � 180 VA max�
Ambient temperature: � � � � � � � � 0 – 40 °C
Dimensions (W × H × D): � � � � � 540 × 1140
Weight: � � � � � � � � � � � � � � � � � � � 33 kg
INTERNATIONAL GmbH & Co. KG. No part of this instruction
®
Frequency Channel
01 863�1 MHz 09
02 864�1 MHz 10
03 863�6 MHz 11
04 864�6 MHz 12
05 863�3 MHz 13
06 864�3 MHz 14
07 863�8 MHz 15
08 864�8 MHz 16
1 ground
1
3
2 signal +, +24 V phantom power
3 signal −, +24 V phantom power
1
1 ground
2 signal +, +24 V phantom power
3
3 signal −, +24 V phantom power
1
1 ground
2 signal +
3
3 signal −
S T
S ground
T signal
× 430 mm
Subject to technical modification .
Frequency
863�2 MHz
864�2 MHz
863�7 MHz
864�7 MHz
863�4 MHz
864�4 MHz
863�9 MHz
864�9 MHz