Listening To Radio - Denon DRA-201SA Mode D'emploi

[2] Setting the loudness mode
Press the MODE button to display
"LOUDNESS".
MODE MODE
1
(Main unit) (Remote control unit)
• The mode switches as shown at the left each
time the button is pressed.
"LOUDNESS" cannot be selected when the
source direct mode is on.
Either turn the FUNCTION dial on the main unit
or use the remote control unit's SELECT
buttons.
VOLUME
/SELECT
(ON)
FUNCTION
(OFF) (ON)
2
(OFF)
(Main unit) (Remote control unit)
• To set to "ON":
Turn the dial clockwise (,) or press the
button.
To set to "OFF":
Turn the dial counterclockwise (.) or press
the button.
H
NOTE:
The maximum total volume increase for the bass,
treble and loudness together is +12. If for example
the bass and treble are set to +12, the sound does
not change when the loudness function is turned on
and off.
[3] Setting the speaker mode
Press the MODE button to display "SPEAKER".
(Refer to page 12.)
MODE MODE
1
(Main unit) (Remote control unit)
All manuals and user guides at all-guides.com
Either turn the FUNCTION dial on the main unit
or use the remote control unit's SELECT
buttons.
VOLUME
/SELECT
FUNCTION
(OFF) (ON)
2
(OFF)
(Main unit) (Remote control unit)
• To set to "ON":
Turn the dial clockwise (,) or press the
button.
To set to "OFF":
Turn the dial counterclockwise (.) or press
the button.
H
[4] Adjusting the balance
Press the MODE button to display "BALANCE"
(Refer to page 12.)
MODE MODE
D
1
(Main unit) (Remote control unit)
"BALANCE" cannot be selected when the
source direct mode is on.
Either turn the FUNCTION dial on the main unit
or use the remote control unit's SELECT
buttons.
(right VOLUME
/SELECT
(left channel channel
volume volume
FUNCTION
adjustment) adjustment)
(Main unit) (Remote
control unit)
2
• If the volume of the right speaker is low:
Turn the dial clockwise (,) or press the
button.
If the volume of the left speaker is low:
Turn the dial counterclockwise (.) or press
the button.
H
• The balance can be set to "CENTER" or
adjusted within the range of +1 to +10 in
steps of 1. When set "CENTER", the
difference between the volume of the left and
right speakers is 0.
8

LISTENING TO RADIO

(1) Tuning
(ON)
BAND MEMORY
ON / STANDBY MODE TIMER / RDS / SET
PHONES FUNCTION
TUNED STEREO AUTO
1 2
D
Example: Tuning in FM 92.50 MHz
(AM stations are tuned in using the same procedure.)
Press the power operation
1
switch to turn on the power.
Press the BAND/RDS button on
the tuner to select the FM AUTO.
2
Use the PRESET/TUNING
UP/DOWN button to tune
the frequency to 92.50.
3
This lights when a station is tuned in.
(left channel
volume
adjustment)
(right
channel
volume
adjustment)
D
The function of the UP/DOWN button on the main
unit may toggle between TUNING UP/DOWN and
VOLUME
PRESET UP/DOWN functions.
PRESET / TUNING
DOWN UP SOURCE DIRECT
• Press the MEMORY/SET button for at least 3
seconds. Then press the UP button.
MHz CH
The function of the UP/DOWN buttons are changed
STEREO RECEIVERER DRA-201SA
to TUNING UP/DOWN.
• Press the MEMORY/SET button for at least 3
3 seconds. Then press the DOWN button. The
function of the UP/DOWN buttons are changed to
PRESET UP/DOWN.
• The UP/DOWN button is factory preset to function
as a TUNING UP/DOWN button.
However, be sure that the UP/DOWN buttons
function as the TUNING UP/DOWN button before
ON / STANDBY
proceeding with step 3.
Auto Tuning
• When a program being broadcast in stereo is
received, the "STEREO" indicator lights and the
BAND
/ RDS
program is received in stereo.
• If reception is poor and there is much noise in the
stereo signals, press the BAND button to set the FM
MONO mode.
• When one of the TUNING UP/DOWN button is
pressed, the frequency changes in steps of 50 kHz in
the FM band, 9 kHz in the AM band.
• If one of the TUNING UP/DOWN button is held for
over 1 second, the frequency continues to change
when the button is released (auto tuning) and stops
PRESET / TUNING
DOWN UP
when a station is tuned in. Tuning will not stop at
stations whose reception is poor.
• To stop the auto tuning function, press the TUNING
UP/DOWN button once.
NOTE:
A humming sound may be heard when using a TV
nearby while receiving AM programs. If this happens,
move the system as far from the TV as possible.
ENGLISH
13