Revell Control FUNTIC 2.0 Mode D'emploi page 9

and neighbouring parts, as well as
physical injury!
• Never use a charger for NiCd/NiMH
batteries!
• Always ensure that the charging
process takes place on a fireproof
surface in a fire-resistant environment.
• Do not leave the battery unsupervised
during the charging process.
• Never disassemble or alter the battery
contacts. Do not damage or puncture
the battery cells. There is a risk of
explosion!
• The LiPo battery must be kept out of
reach of children.
• When disposing of batteries, they
must be discharged or their capacity
must be fully depleted. Cover exposed
terminals with adhesive tape in order
to prevent short-circuiting!
Maintenance and care:
• Please only use a clean, damp cloth
to wipe off the model.
• Protect the model and batteries from
direct sunlight and/or direct heat.
1A ON/OFF switch
1B Battery compartment
2 REMOTE CONTROL
2A Control for thrust and rotation /
Press vertically: Headless Mode
2B Control for Forward/Reverse and Banking /
Press vertically: Return to Home
2C Short press: Motor start and landing /
Long press: Emergency motor shut-down
2D Flip function
16
• Never allow the transmitter and
charging unit to come into contact
with water, because the electronics
will be damaged as a result.
Technical changes and differences in
color reserved!
Required batteries for the model:
Power supply:
Rated output: 1 x DC 3,7 V / 1,1 Wh
Batteries: 3,7 V rechargeable
LiPo battery (included)
Capacity: 300 mAh
Battery requirement for the
remote control:
Power supply:
DC 4,5 V
Batteries: 3 x 1.5 V "AA"
(not included)
USB charger:
Power supply: DC 5V via USB port,
500 mA or higher
Rated output: 4,2 V / 500 mAh max.
1 MODEL
1C Battery connection cable
2E Power LED
2F ON/OFF switch
2G Trim for rotation
2H Trim for forward/backwards
2I Trim for banking
2J Buttons for flight speed
2K Battery compartment cover
3 INSERTING BATTERIES (REMOTE CONTROL)
3A Open the battery compart- 3B Insert 3 x 1.5 V AA batteries
ment cover (2K) to open the and pay attention to the
battery compartment. polarity specifications, as
indicated in the battery
compartment.
4 CHARGING THE MODEL
Attention: The battery and motor must cool down for 15 to 30 minutes before charg-
ing and after every flight. Otherwise they can be damaged. The charging process must
be constantly monitored. Always ensure that the charging process takes place on a
fireproof surface in a fire-resistant environment.
• Remove the battery from the model (4A). Plug the USB charger into an open USB port (4B).
• Plug the white battery plug into the socket of the charger. Make sure that the polarity is
correct in the process (4C). The battery must be gently inserted into the charging
socket – DO NOT USE FORCE. If the battery is not correctly inserted into the charging
socket, the battery may become damaged and, under certain circumstances, cause
injury.
• The red LED on the USB charger illuminates when the charging process starts.
• The charging process lasts approx. 60 minutes and must be continuously monitored.
The red LED on the charger goes out as soon as the charging process is finished.
• Disconnect the battery from the charger and disconnect the charger from the USB
port once charging is complete.
The model can fly for approx. 5-7 minutes after a charge time of approx.
60 minutes.
Warning notice: The battery does not normally heat up while charging. If it should
become warm or even hot and/or changes to the surface begin to appear, immediately
discontinue the charging process!
5 START PREPARATION
The model must be switched on first in order to connect it to the remote control. To do
this, push the battery into the battery compartment (1B) on the model and insert the
battery plug in the connection socket (1C) in the model. Do not use force and ensure the
correct polarity (5A). Then place the model on an even, flat and stable surface. Then set
the ON/OFF switch on the model (1A) to the ‚ON' position.
Press the ON/OFF switch 2F on the remote control to switch it on. A short signal tone
from the remote control indicates that the model is ready for start-up (5B). Pressing
button 2C starts the rotors.
Attention: If the model does not land correctly, please press and hold button (2C) for
approximately 2 seconds.
Warning: The motors shut down immediately!
Once you have finished flying, switch the model off first and then the remote control.
Unplug the battery from the model and remove the battery from the model.
3C Close the battery
compartment cover.
17