Kettler UNIX 2 Instructions De Montage page 3

– EN –
! WARNING!
Please note that there is always a danger of injury
when working with tools or doing manual work. Therefore
please be careful when assembling this machine.
■
Ensure that you have received all the parts required (see check
list) and that they are undamaged. Should you have any cause
for complaint, please contact your KETTLER dealer.
■
Before assembling the equipment, study the drawings carefully
and carry out the operations in the order shown by the dia-
grams. The correct sequence is given in capital letters.
■
The equipment must be assembled with due care by an adult
person. If in doubt call upon the help of a second person, if pos-
sible technically talented.
Handling the equipment
■
Before using the equipment for exercise, check carefully to en-
sure that it has been correctly assembled.
■
It is not recommended to use or store the apparatus in a damp
room as this may cause it to rust. Please ensure that no part of
the machine comes in contact with liquids (drinks, perspiration
etc.). This may cause corrosion.
■
The machine is designed for use by adults and children should
not be allowed to play with it. Children at play behave unpre-
dictably and dangerous situations may occur for which the ma-
nufacturer cannot be held liable. If, in spite of this, children are
allowed to use the equipment, ensure that they are instructed in
its proper use and supervised accordingly.
■
The equipment is independent of revolutions per minute.
Maintainance – Service – Spare Parts
■
Damaged components may endanger your safety or reduce the
lifetime of the equipment. For this reason, worn or damaged
parts should be replaced immediately and the equipment taken
out of use until this has been done. Use only original KETTLER
spare parts.
■
To ensure that the safety level is kept to the highest possible
standard, determined by its construction, this product should be
serviced regulary (once a year) by specialist retailers.
■
Please ensure that liquids or perspiration never enter the ma-
chine or the electronics.
Spare parts order
■
When ordering spare parts, always state the full article num-
ber, spare-partnumber, the quantity required and the S/N of
the product (see handling).
Example order: Art. no. 07692-200 / spare-part no.
943192085 / 2 pieces / S/N ....................
■
The fastening material required for each assembly step is shown
in the diagram inset. Use the fastening material exactly as in-
structed.
■
Bolt all the parts together loosely at first, and check that they
have been assembled correctly. Tighten the locknuts by hand
until resistance is felt, then use spanner to finally tighten nuts
completely against resistance (locking device). Then check that
all screw connections have been tightened firmly. Attention:
once locknuts have been unscrewed they no longer function cor-
rectly (the locking device is destroyed), and must be replaced.
■
For technical reasons, we reserve the right to carry out prelimi-
nary assembly work (e.g. addition of tubing plugs).
■
A slight production of noise at the bearing of the centrifugal
mass is due to the construction and has no negative effect upon
operation. Possibly occurring noise during reverse pedalling re-
sult from engineering and are absolutely safe.
■
The training device has a electromagnetic brake system.
■
To operate correctly, the pulse function requires a minimum vol-
tage of 2,7 volts (only for computers working with batteries).
■
Before beginning your first training session, familiarize yourself
thoroughly with all the functions and settings of the unit.
■
Calibration of the device can only be carried out by the manu-
facturer. Note: a calibration diagram is included.
Waste Disposal
KETTLER products are recyclable. At the end of its use-
ful life please dispose of this article correctly and safely
(local refuse sites).
KETTLER GB Ltd.
GB
Kettler House, Merse Road
North Moons Moat
Redditch, Worcestershire B98 9HL
www.kettler.co.uk
KETTLER International Inc.
USA
1355 London Bridge Road
Virginia Beach, VA 23453
www.kettlerusa.com
+44 1527 591901
+44 1527 62423
e-mail: sales@kettler.co.uk
+1 888 253 8853
+1 888 222 9333
info@kettlerusa.com
e-mail:
5