VISIOMED ThermoFlash PRO LX-261 EVOLUTION Manuel D'utilisation page 23

EMC data
Guidance and manufacturer's declaration - electromagnetic immunity – for
ME equipment and ME systems that are not life-supporting. The PRO LX-261
EVOLUTION is intended for use in the electromagnetic environment specified
below. The customer or the user of the PRO LX-261 EVOLUTION should assure
that it is used in such an environment.
EN
Immunity 60601 Compliance
test test level
level
Conducted Portable and mobile RF communications equipment should
3 Vrms 3V
RF be used no closer to any part of the model PRO LX-26E, in-
cluding cables, than the recommended separation distance
150 kHz
IEC
calculated from the equation applicable to the frequency of
to 80
61000-4-6
the transmitter.
MHz
Recommended separation distance
Radiated
3 V/m 3 V/m
d =
RF
80 MHz
IEC
d =
to 2.5
61000-4-3
GHz
d =
where
ing of the transmitter in watts (W) according to
the transmitter manufacturer and d is the recom-
mended separation distance in meters (m).b
Fields strengths from fixed RF transmitters, as determined
by an electromagnetic site survey, a should be less than the
compliance level in each frequency range.b
Interference may occur in the vicinity of equipment marqued
with the following symbol:
Note 1: At 80 MHz and 800 MHz, the higher frequency range applies.
Note 2: These guidelines may not apply in all situations. Electromagnetic is affected by
absorption and reflection from structures, objects and people.
a. Fields strengths from fixed transmitters, such as base stations for radio (cellular/
cordless) telephones and land mobile radios, amateur radio, AM and FM radio broad-
cast and TV broadcast cannot be predicted theoretically with accuracy. To assess the
electromagnetic environment due to fixed RF transmitters, an electromagnetic site
survey should be considered. If the measured field strength in the location in which
the model PRO LX-261E is used exceeds the applicable RF compliance level above. The
44 Visiomed - PRO LX-261E - 122015
Electromagnetic
environment - guidance
[ 3.5
] √
P
V1
[ 3.5
] √
P 80 MHz to 800 MHz
E1
[ 7
] √
P 800 MHz to 2.5 GHz
E1
P is the maximum output
model PRO LX-261E should be observed to verify normal operation. If abnormal per-
formance is observed, additional measures may be necessary such as reorienting or
relocating the model PRO LX-261E.
b. Over the frequency range 150 kHz to 80 MHz, field strengths should be less than
3V/m.
Recommended separation distances between portable and mobile RF communi-
cations equipment and the equipment or system - for equipement and systems
that are not life-supporting. The model PRO LX- 261E is intended for use in an electro-
magnetic environment in which radiated RF disturbances are controlled. The customer
or the user of the model PRO LX-261E can help prevent electromagnetic interference
by maintaining a minimum distance between portable and mobile RF communications
equipment (transmitters) and the model PRO LX-261E as recommended below, acord-
ing to the maximum output power of the communications equipment.
Rated maximum
output
of transmitter
0.01
0.1
1
power rat-
10
100
For transmitters rated at a maximum output power not listed above the recommended
separation distance d in meters (m) can be estimated using the equation applicable to
the frequency of the transmitter, where P is the maximum output power rating of the
transmitter in watts (W) according to the transmitter manufacturer.
Note 1: At 80 MHz and 800 MHz, the separation distance for the higher frequency
range applies.
Note 2: These guidelines may not apply in all situations. Electromagnetic propaga-
tions is affected by absorption and reflection from structures, objects and people.
Separation distance according to frequency of transmitter m
80 MHz to 800 MHz
800 MHz to 2.5 GHz
[ 3.5 [ 3.5
d = ] √ d = ] √
P P
V1 E1
0.12 0.12
0.38 0.38
1.2 1.2
3.8 3.8
12 12
Visiomed - PRO LX-261E - 122015
800 MHz to 2.5 GHz
[ 7
] √
P
d =
E1
0.23
0.73
2.3
7.3
23
45