Télécharger Imprimer la page

Operation; Cleaning; Storage; Maintenance - Scheppach CMT200-20ProS Traduction Des Instructions D'origine

Publicité

Les langues disponibles
  • FR

Les langues disponibles

  • FRANÇAIS, page 24
To switch off the machine, slide the slide switch to
position "O (OFF)".
Adjusting the number of pendulum strokes (Fig.
1)
The number of pendulum strokes is adjustable. To
change the number of pendulum strokes, turn the ad-
justing dial between 1 and 6. The higher the number,
the higher the number of pendulum strokes. Before
starting work, set the adjusting dial to the appropriate
number for your workpiece.
NOTE:
The adjusting dial cannot be turned directly from 1 to
6 or from 6 to 1. Continuing to turn the adjusting dial
by force may damage the machine. If you change the
direction of rotation of the adjusting dial, always move
it through all intermediate positions.

12. Operation

WARNING:
• Keep hands and face away from the application tool
before starting the machine and during operation .
Caution
• Do not exert excessive pressure on the machine as
this may cause the motor to block and the machine
to stop.
Cutting, sawing and scraping
CAUTION:
• Do not force the machine in the direction of use
(e.g. to both sides) without a cutting edge. This can
damage the machine.
• Set the application tool on the workpiece. Then
push the machine forward so that the movement of
the application tool does not slow down.
NOTE:
• Violent feeding or excessive pressure on the ma-
chine can reduce the performance of the work.
• Before starting cutting work, it is recommended to
preset the pendulum stroke number to 4 - 6.
• Remove sawdust by pulling the tool accordingly.
This improves work performance.
• The circular saw is recommended for cutting long
straight lines.
Sanding
CAUTION:
• Use sandpaper that has been used to sand metal,
not wood.
• Do not use worn sandpaper or sandpaper without
grit. Bring the sandpaper into contact with the work-
piece.
22 | GB
 www.scheppach.com /  service@scheppach.com /  +(49)-08223-4002-99 /  +(49)-08223-4002-58
NOTE:
• A grinding sample on a test material is recommend-
ed in order to determine the pendulum stroke num-
ber suitable for your work.
• Use sandpaper with the same grain size until sand-
ing of the whole workpiece is finished. If the sand-
paper grain size is changed during work, a fine sur-
face finish may not be obtained.

13. Cleaning

Danger!
Always pull out the battery pack before starting any
cleaning work.
Cleaning
• Keep all safety devices, air vents and the motor
housing free of dirt and dust as far as possible.
Wipe the equipment with a clean cloth or blow it
with compressed air at low pressure.
• We recommend that you clean the device immedi-
ately each time you have finished using it.
• Clean the equipment regularly with a moist cloth
and some soft soap. Do not use cleaning agents
or solvents; these could attack the plastic parts of
the equipment. Ensure that no water can seep into
the device. The ingress of water into an electric tool
increases the risk of an electric shock.

14. Storage

Store the device and its accessories in a dark, dry
and frost-proof place that is inaccessible to children.
The optimum storage temperature is between 5 and
30˚C. Store the electrical tool in its original packag-
ing. Cover the electrical tool in order to protect it from
dust and moisture. Store the operating manual with
the electrical tool.

15. Maintenance

There are no parts inside the equipment which re-
quire additional maintenance.
Service information
Please note that the following parts of this product
are subject to normal or natural wear and that the fol-
lowing parts are therefore also required for use as
consumables.
Wear parts*: Attachment - plunge saw blade; Attach-
ment - scraper; Attachment - grinder
* Not necessarily included in the scope of delivery!

Publicité

loading

Ce manuel est également adapté pour:

5909224900