Hitachi C 10FC2 Mode D'emploi Et Instructions De Securite page 66

Compound Saw Parts List.
ITEM
No.
TRUSS HD. SCREW 1/4" × 1/2"
1
2 LINK
MACHINE SCREW M5 × 16
3
WASHER 3/16" × 3/4"
4
5 COLLAR
6 GUARD RETAINER
7 BLADE GUARD (PLASTIC)
8 SPRING GUARD
9 RIVET
WASHER 3/16" × 3/8"
10
BOLT (LEFT HAND) W/WASHER M8 × 20
11
12 WASHER
13 ARBOR COLLAR
HEX. SOCKET HD. BOLT M5 × 20
14
15 HITACHI LABEL
16 WARNING LABEL (B)
17 WARNING LABEL (C)
MACHINE SCREW M5 × 12
18
19 BLADE GUARD (METAL)
20 FLAT HD. SCREW 32UNFX13/16"
21 SLEEVE RUBBER
22 REAR LOWER GUARD
23 SPRING
24 E-RING
25 BRACKET STOP
26 CAP RUBBER
RIVET 3/16" × 17/32"
27
28 CUTTER SHAFT GUARD
29 SCREW STOP
30 CHUCK NUT M16
WASHER M16 × 30
31
32 ANGLE REGULATOR
33 PLATE LOCK
CR. RE. PAN HD. ROUND NECK SCREW M6 × 12
34
35 SLIDE PLATE
36 TORSION SPRING
37 ANGLE POINTER
MACHINE SCREW M4 × 6
38
MACHINE SCREW (W/WASHER) M5 × 14
39
40 CHIP DEFLECTOR
HEX. BOLT M10 × 65
41
HEX. BOLT M10 × 35 (W/WASHER)
42
HEX. SOCKET SET SCREW M5 × 10
43
44 FENCE
WING SCREW M5 × 20
45
HEX. SOCKET SET SCREW M5 × 10
46
47 SCREW
48 COMPRESSION SPRING
66
PARTS NAME
ITEM
No.
49 CLAMP LEVER
50 HANDLE COLLAR
WASHER 3/8" × 29/32"
51
HEX. SOCKET SET SCREW M6 × 12
52
53 PIVOT SHAFT
BOLT M6 × 25
54
55 NUT M6
56 TILT BRACKET
DRIVE SCREW D2.3 × 5
57
58 NUT CHUCK M8
59 FLAT WASHER M8
60 TABLE
61 HANDLE BAR
62 STEEL BALL D8
MACHINE SCREW M5 × 10
63
64 LOCATION SEAT
MACHINE SCREW M4 × 8
65
TILT POINTER
66
67 TABLE INSERT
68 PLATE SPRING
TAPPING SCREW D5 × 10
69
70 FOLLOWER PLATE
71 WARNING LABEL (A)
72 ROTATION SLIDE PLATE
73 TILTING SCALE
74 BASE
75 CENTER SHAFT
76 NUT M10
77 ADJUST SCREW M10
78 MOTOR ASS'Y 115V (INCLUD. 101, 111, 118-123, 126-136)
79 SPECIAL BOLT
HEX. SOCKET HD. BOLT M8 × 20
80
81 SEGMENT HANDLE
82 CORD GUARD
83 CORD
MACHINE SCREW M5 × 20
84
85 CUSHION
86 CORD CLAMP
TAPPING SCREW D4 × 20
87
88 CORD CLAMP
89 STRAIN RELIEF
TRUSS HD. TAPPING SCREW D4 × 12
90
91 SWITCH
92 STOPPER
93 SPRING
94 LOCK-OFF BUTTON
TAPPING SCREW (W/WASHERS) D5 × 20
95
96 NUT M4
PARTS NAME