Programming The Remote Controls; General Information; Memorising The Keygo Io Remote Controls; Memorising 3-Button Remote Controls - SOMFY Elixo 500 3S io Manuel D'installation

EN
P40 Coupling speed when closing
P41 Coupling speed when opening
Values 1: slowest speed
to
4: fastest speed
Default value: 2
Warning
Comments
If parameters P40 or P41 are changed, the
installer must check that the obstacle detection
system complies with appendix A of standard EN
12 453. If necessary, install a safety edge and
check that compliance is obtained.
Failure to follow this instruction may result in
serious injury, e.g. due to crushing by the gate.

8. PROGRAMMING THE REMOTE CONTROLS

8.1. General information

8.1.1. Memorising the remote controls
There are two ways to memorise a remote control:
• Memorising via the programming interface.
• Memorising by copying a previously memorised remote control.
Each control button is memorised individually.
Memorising a button which has already been memorised will clear this
button's function.
8.1.2. Meaning of displayed codes
Code Description
Add Successful memorisation of a remote control
dEL Delete a previously memorised button
FuL Memory full

8.2. Memorising the Keygo io remote controls

8.2.1. Via the programming interface
1) Press the "PROG" button for 2 s.
The screen displays "F0".
NB: pressing "PROG" again allows the next function to be memorised.
2) Press the outer le and right buttons on the remote control together.
The remote control indicator light flashes.
3) Briefly press the button selected to control the function (complete
opening, pedestrian opening, lighting, auxiliary output).
The screen displays "Add".
Complete opening control - Fig. 27
PEDESTRIAN opening control - Fig. 28
LIGHTING control - Fig. 29
AUXILIARY OUTPUT control (P15 = 4, 5 or 6) - Fig. 30
11
8.2.2. Memorising by copying a previously memorised
Keygo io remote control - Fig. 31
This operation is used to copy the programming from a previously memo-
rised remote control button.
1) Press the outer le and right buttons on the previously memorised
remote control simultaneously until the green indicator light flashes.
2) Press and hold the button to be copied on the previously memorised
remote control for 2 seconds.
3) Briefly press the outer le and right buttons on the new remote control
together.
4) Briefly press the selected button to actuate the motorisation on the
new remote control.

8.3. Memorising 3-button remote controls

8.3.1. Via the programming interface - Fig. 32
1) Press the "PROG" button for 2 s.
The screen displays "F0".
NB: pressing "PROG" again allows the next function to be memorised.
2) Press "PROG" at the rear of the 3-button remote control to memorise
the function.
The screen displays "Add".
8.3.2. By copying a previously memorised 3-button mo-
no-directional io remote control - Fig. 33
A = "source" remote control already memorised
B = "target" remote control to be memorised
8.3.3. Button functions on a 3-button remote control
F0 Complete opening
F1 Complete opening
F2 Lighting ON
F3 Aux. output ON
9. CLEARING THE REMOTE CONTROLS
AND ALL SETTINGS

9.1. Clearing memorised remote controls - Fig. 34

Press the "PROG" button for 7 s.
Causes all memorised remote controls to be cleared.

9.2. Clearing all settings - Fig. 35

Press and hold the "SET" button for 7 s.
Clears the auto-programming and resets the default values for all param-
eters.
my
Stop Complete closing
Complete closing
If gate is closed
pedestrian opening
Otherwise stop
Lighting OFF
Aux. output OFF
Copyright © 2017 SOMFY ACTIVITES SA. All rights reserved.
Elixo 500 3S io