Locking The Programming Buttons - Fig; Diagnostics; Operating Codes Display; Programming Codes Display - SOMFY Elixo 500 3S io Manuel D'installation

Elixo 500 3S io
10. LOCKING
BUTTONS FIG. 36
Warning
The keypad must be locked to ensure the safety of the users.
Failure to follow this instruction may result in serious injury, e.g.
due to crushing by the gate.
Locks the programming (end limits, auto-programming, parameter set-
tings).
When the programming buttons are locked, a dot appears a er the 1st
digit.
Pressing the "SET", "+", "-" buttons:
• - the "SET" button must be pressed first.
• the "+" and "-" buttons must be pressed simultaneously within 2
seconds.
To access the programming again, repeat the same procedure.

11. DIAGNOSTICS

11.1. Operating codes display

Code Description
C1 Awaiting command
C2 Gate opening
C3 Awaiting gate closure Automatic closing time delay P02, P04
C4 Gate closing
C6 Detection in progress
for cell safety
C7 Detection in progress
for safety edge safety
C8 Detection in progress
for programmable
safety
C9 Detection in progress
for emergency stop
safety
C12 Reinjecting current
C13 Safety device autotest
in progress
C14 Permanent complete
opening wire control
input
C15 Permanent pedestrian
opening wire control
input
BUS cell programming
C16
refused
Cc1 9.6 V power supply
Cu1 24 V power supply
Copyright © 2017 SOMFY ACTIVITES SA. All rights reserved.
THE PROGRAMMING
Comments
or P05 in progress.
Displayed during a movement request
or during movement when detection is
in progress on the safety input.
The display appears for as long as
detection is in progress on the safety
input.
Displayed while the autotest is running
on the safety devices.
Indicates that the complete opening
wire control input is permanently
activated (contact closed). Commands
coming from the radio remote controls
are then disabled.
Indicates that the pedestrian opening
wire control input is permanently
activated (contact closed). Commands
coming from the radio remote controls
are then disabled.
Check that the BUS cells (wiring, align-
ment, etc.) are operating correctly
Displayed during operation with 9.6 V
backup battery
Displayed during operation with 24 V
backup battery

11.2. Programming codes display

Code Description
H0 Awaiting setting
Hc1 Awaiting setting +
9.6 V power supply
Hu1 Awaiting setting + 24
V power supply
H1 Awaiting start of
auto-programming
H2 Auto-programming
mode - opening
H4 Auto-programming
mode - closing
F0 Awaiting remote
control memorisa-
tion for operation in
complete opening
mode
F1 Awaiting remote
control memorisa-
tion for operation in
pedestrian opening
mode
F2 Awaiting remote
control memori-
sation for remote
lighting control
F3 Awaiting remote
control memori-
sation for auxiliary
output control
Comments
Pressing and holding the "SET" button
for 2 seconds starts auto-programming
mode.
Displayed during operation with 9.6 V
backup battery
Displayed during operation with 24 V
backup battery
Pressing the "OK" button starts the
auto-programming cycle.
Pressing the "+" or "-" button allows
the motor to be controlled in forced
operation mode.
Pressing a button on the remote control
allocates this button to the motor com-
plete opening control.
Pressing "PROG" once more switches to
"awaiting remote control memorisation
for operation in pedestrian opening mode:
F1".
Pressing a button on the remote control
allocates this button to the motor pedes-
trian opening control.
Pressing "PROG" once more switches
to "awaiting remote lighting control
memorisation: F2".
Pressing a button on the remote control
allocates this button to the remote
lighting control.
Pressing "PROG" once more switches
to "awaiting auxiliary output control
memorisation: F3".
Pressing a button on the remote control
allocates this button to the remote
lighting control.
Pressing "PROG" once more switches to
"awaiting remote control memorisation
for operation in complete opening mode:
F0".
EN
12