Using The Talkover Function; Listening To Channel Pre-Fader Signals; Troubleshooting - Teac Tascam MZ-372 Mode D'emploi

Using the talkover function

When the talkover function is turned on by pressing
the TALKOVER ( ) switch, the levels of channels 1–6
3
will be automatically lowered when sound is input
from a mic connected to the MAIN MIC INPUT (
jack, making the mic signal easier to hear.
To turn the talkover function off, press the TALKOVER
( ) switch to turn it off (TALKOVER (
3
comes unlit).

Listening to channel pre-fader signals

By pressing the PFL (
) switches of channels to turn
y
them on, you can enable headphone monitoring of in-
dividual channels 1–6, even when their faders (
set at minimum values.
You can also monitor the signal before it is sent to the
stereo output bus.
1.
Press the PFL ( ) switches for the channels you
y
want to monitor so that their PFL indicators light,
and turn the MIXING (
To monitor the signal before it is sent to the stereo
output bus, turn the MIXING (
ITOR.
2.
After making mixing adjustments, use the
PHONES VOLUME (
toring output level.
NOTE
i The L/R SPLIT (o) switch can be turned on/off to
change the headphone output mode.
i When the L/R SPLIT switch (o) is on (indicator lit),
the pre-fader signals are output from the left chan-
nel and the monitoring signal is output from the
right channel.
i When the L/R SPLIT switch (o) is off (indicator un-
lit), the pre-fader signals and the monitoring signal
are mixed and output together from both head-
phone channels.
i When the PFL (y) switch is off, if the L/R SPLIT
(o) switch is set to on, the monitoring signal will
be output from the right channel and no sound
will be output from the left channel of the head-
phones.

Troubleshooting

If you are having trouble with the operation of this
unit, please try the following before seeking repair.
If these measures do not solve the problem, please
contact the store where you purchased this unit or
TASCAM customer support service.
) indicator be-
3
6
) knob to PFL.
u
) knob to MON-
u
) knob to adjust the moni-
i
The unit will not turn on.
0 Confirm that the AC adapter (TASCAM PS-M1524)
is securely connected to both the outlet and the
DC jack.
)
w
Sound is not output from speakers connect-
ed via the MAIN OUTPUTS 1-2 jacks.
0 Check the settings and volume of the connected
amplifier.
0 Confirm that channel faders (
0 Confirm that the input sound source is connected
properly.
The volume is low even when faders are
) are
raised.
0 Confirm that the GAIN (
are set properly.
0 If mics are being input on channels 1–6, confirm
that the INPUT LEVEL (
The sound is distorted.
0 Confirm that the GAIN (
are set properly.
0 Confirm that the EQ is not set too high.
0 Confirm that the channel 1–6 (
OUTPUT VOL (
Sound from a record player is strange.
0 Confirm that it is connected to channel 2–4 LINE
A ( ) input jacks and the LINE/PHONO (
v
switch is set to PHONO.
0 Confirm that the grounding wire from the record
player is connected to the | (GND) (
tor.
A connected device is making a humming
noise.
0 Connect a grounding wire from the metal frame of
the connected device to the | (GND) (
tor on this unit.
No sound is output from the monitoring sys-
tem connected to the MONITOR OUT jacks.
0 Check the settings of the connected monitoring
system.
0 Confirm that the channel 1–6 GAIN (
channel faders (
) are raised.
6
) knobs for channels 1–6
4
) switches are set to LINE.
j
) knobs for channels 1–6
4
) faders and MAIN
6
) knob are not set too high.
8
b
) knobs and
4
) are raised.
6
TASCAM MZ-372
) input
k
) connec-
) connec-
b
15