Turning The Power On And Off - Teac Tascam MZ-372 Mode D'emploi

Connecting microphones
Mics can be connected to the MAIN MIC INPUT (
jack on the front of the unit or to one of the channel
1–6 C (MONO) /MIC (
) input jacks on the back of the
h
unit with the INPUT LEVEL (
Connecting electronic devices and other
audio equipment
When connecting an electronic device or other audio
equipment, connect it to channel 1–6 C (MONO) /MIC
) input jacks, and set the INPUT LEVEL switch (
(
h
to LINE. The device can be connected to channel 1–6
LINE A or B ( ) input jacks.
v
When connected to channel 2–4 LINE A (
jacks, set the LINE/PHONO (
NOTE
The C (MONO) /MIC (
Connecting record players
When connecting a record player, connect it to chan-
nel 2–4 LINE A ( ) input jacks, and set the LINE/PHO-
v
NO ( ) input switch to PHONO.
k
Connect the grounding wire from the record player to
the | (GND) ( ) connector.
b
Connecting monitor speakers
Connect monitor speakers (powered speakers or an
amplifier and speaker system) to the MONITOR OUT
( ) jacks.
z
To mix in the mic input signal from the MAIN MIC IN-
PUT (
) jack, and output it from the monitor speakers,
w
set the MONITOR OUT (
MIC.
Connecting headphones
Connect headphones to the PHONES (
dard stereo).
You can monitor input channel pre-fader signals and
the signal before it is sent to the stereo output bus.
CAUTION
Before connecting headphones, minimize the vol-
ume with the PHONES VOLUME (
to do so could result in a sudden loud noise that
could harm hearing, for example.
NOTE
Since the headphone sound is output from the
monitoring bus, the position of the MAIN OUTPUT
VOL (
) knob has no effect on it.
8
) switch set to MIC.
j
) input
v
) input switch to LINE.
k
) jacks are mono inputs.
h
) mic mix switch to WITH
s
) jack (stan-
p
) knob. Failure
i
Connecting stereo amplifiers
) When connecting a stereo amplifier, connect it to the
w
MAIN OUTPUTS 1-2 (UNBALANCED) (
OUTPUTS 1-2 (BALANCED) (
TIP
i When connecting 2 or more amplifier and speaker
systems, including main and sub, main and mon-
itoring, or front and rear combinations, using the
MAIN OUTPUTS 1-2 (UNBALANCED) (
OUTPUTS 1-2 (BALANCED) (
)
j PUT (
) jacks could be convenient. Moreover, the
x
outputs of the jacks are independent and have
their own dedicated output knobs, so you can set
the output levels separately with this unit.
i By connecting a recorder to MONITOR OUT (
jacks, the signal output to amplifier/speaker sys-
tems can be recorded.

Turning the power on and off

CAUTION
i Turn down the volume of the sound system con-
nected to the unit before starting up or shutting
down the unit.
i Do not wear connected headphones when turning
the unit on and off. Loud noises could damage the
speakers or harm your hearing.
Before turning the power on
1.
Make the following settings on the front of the
unit.
o EQ knobs w center values
o Other knobs w all the way left (MIN side)
o Faders w all the way down
o Switches w off (not pushed in)
2.
Minimize the output levels of audio sources and
input levels of amplifiers connected to this unit.
Turning the power on
1.
Use the POWER (
to turn its power on.
The POWER (
will light when on.
2.
Turn connected input audio source devices on.
3.
Finally turn amplifiers on.
Turning the power off
Follow the procedures above in reverse when turning
the power off.
Failure to follow the correct order could result in click-
ing noises, for example, that might damage equip-
ment.
f
) jacks.
c
), and SUB OUT-
c
) switch on the back of the unit
a
) indicator on the front of the unit
9
TASCAM MZ-372
) or MAIN
), MAIN
f
)
z
13