Initial Operation; Electrical Connection - Scheppach OSM100 Traduction Des Instructions D'origine

• Mark holes on board where belt/disc sander is to
be mounted.
• Follow last three steps in section Mounting Belt/
Disc Sander to Workbench.
Note! If lag bolts are used, make sure they are long
enough to go through holes in belt/disc sander base
and material the belt/ disc sander is being mounted
to. If machine bolts are used, make sure bolts are
long enough to go through holes in belt/disc sander,
the material being mounted to, and the lock washers
and hex nuts.
Connection to vacuum suction.
The use of an extraction system is recommended.
Tool changes, Fig. 2–7
m ATTENTION!! Turn off the machine and discon-
nect the main plug.
When changing tools make sure to have all parts
cleaned.
Prepare the appropriate tool and mount it as follows:
1. Attach the lower spindle disc (16) to the spindle
(4) (fig. 2).
2. Insert the table inlays (5) into the table (fig. 3).
3. Attach the lower spindle disc (6) to the spindle
(4) (fig. 2).
4. Slide the abrasive sleeve (7) onto the rubber
sleeve (6) (fig. 5).
5. Apply the disc (13) (use the correct measure-
ments) (fig. 6).
6. Put on the hex-nut and tighten it with the hook
wrench (14). (fig. 7)
Be sure always to mount the correct parts when
changing the abrasive sleeves. The table inlays have
to be bigger than the abrasive sleeves. (fig. 8)
Note! The 13 mm abrasive sleeve is put directly onto
the spindle (4).
Table:
Abrasive Table inlay
sleeve inside D inside D
13 mm 18 mm
19 mm 25 mm
26 mm 31 mm
38 mm 44 mm
51 mm 57 mm
76 mm 82 mm

9. Initial operation

After completing all assembly and setup work, turn
on the machine and while it idles, check that the
spindle can move faultlessly. In the case of distur-
bances, turn the machine off immediately and rectify
the cause.
 www.scheppach.com /  service@scheppach.com /  +(49)-08223-4002-99 /  +(49)-08223-4002-58
Spindle disc
size
small 16 mm
medium 20 mm
medium 20 mm
large 35 mm
large 35 mm
large 35 mm
Once the machine has reached its maximum revolu-
tion speed you ay start the grinding work.
Move the work piece slowly in the direction contrary
to the running direction of the grinding roll.
Do not overload the machine by too much pressure
against the grinding roll.
After finishing the grinding turn off the machine and
disconnect the main plug.
Attention!! Use dust mask, protective goggles
and vacuum extraction.

10. Electrical connection

The electrical motor installed is connected and
ready for operation. The connection complies
with the applicable VDE and DIN provisions. The
customer's mains connection as well as the ex-
tension cables used must also comply with these
regulations.
17.1 Damaged electrical connection cable
The insulation on electrical connection cables is often
damaged.
This may have the following causes:
• Pressure points, where connection cables are
passed through windows or doors
• Kinks where the connection cable has been improp-
erly fastened or routed
• Places where the connection cables have been cut
due to being driven over
• Insulation damage due to being ripped out of the
wall outlet
• Cracks due to the insulation ageing
Such damaged electrical connection cables must not
be used and are life-threatening due to the insulation
damage.
Check the electrical connection cables for damage
regularly. Ensure that the connection cables are dis-
connected from electrical power when checking for
damage.
Electrical connection cables must comply with the ap-
plicable VDE and DIN provisions. Only use connec-
tion cables of the same designation.
The printing of the type designation on the connection
cable is mandatory.
Connections and repair work on the electrical equip-
ment may only be carried out by electricians.
17.2 AC motor
• The mains voltage must be 220–240 V~.
• Extension cables up to 25 m long must have a
cross-section of 1.5 mm².
• Extension cables over 25 m long must have a cross-
section of 2.5 mm².
GB | 19