Balluff BML-S1C0-Q53-M400-0-KA Serie Mode D'emploi page 14

BML-S1C0-Q53_-M400-_0-KA_ _
Magnetic Linear Encoder System
Content
1 Safety Advisories .................. 2
1.1 Intended use .......................... 2
1.2 Qualified personnel ................ 2
1.3 Use and testing ...................... 2
1.4 Validity .................................... 2
2 Function and
Characteristics ..................... 3
2.1 Characteristics ....................... 3
2.2 Principle of operation ............. 3
2.3 Interface signals ..................... 3
3 Sensor Installation ............... 4
3.1 Installing the sensor and tape
(linear motion) ......................... 4
Distances, tolerances ............. 4
Attaching sensor head ........... 5
3.2 Installing sensor and magnet
ring (rotary motion) ................. 5
4 Wiring .................................... 6
4.1 Cable assignments ................. 6
4.2 Interfaces ............................... 6
5 Selecting the Appropriate BML
and Controller System ........... 7
5.1 Selecting the BML .................. 7
5.2 Selecting the controller .......... 7
5.3 BML system with magnet ring .. 8
6 Startup ................................... 9
6.1 Turn on system ....................... 9
6.2 Check system function ........... 9
6.3 Regular checking ................... 9
6.4 Malfunction ............................ 9
7 Accessories .......................... 9
7.1 Cover strip .............................. 9
8 Troubleshooting .................. 10
9 Technical Data .................... 11
10 Scope of Delivery ............... 11
11 Versions (indicated
on part label) ....................... 12
2
english
1 Safety Advisories
Read this manual before installing
the sensor and placing it in
operation.
1.1 Intended use
The BML displacement sensor is
fitted into a machine or piece of
equipment for its application.
Together with a controller (PLC) it
comprises a displacement
measurement system and may be
used only for this purpose.
Unauthorized modifications and
non-allowed use will result in loss of
guarantee and warranty.
1.2 Qualified personnel
This manual is intended for
technical personnel who are
involved in installation and setup.
The CE Mark verifies
that our products
meet the requirements
of EC Directive
89/336/EEC (EMC Directive)
and the EMC Law. Testing in our
EMC Laboratory, which is
accredited by DATech for Testing
Electromagnetic Compatibility, has
confirmed that Balluff products
meet the EMC requirements of the
following Generic Standards:
EN 61000-6-4 (emission)
EN 61000-6-2 (noise immunity)
1.3 Use and testing
Prevailing safety regulations and
codes must be observed for using
the displacement sensor.
In particular, measures must be
taken to ensure that a defect in the
displacement sensor will not result
in hazards to persons or equipment.
This includes installation of additio-
nal safety limit switches, emergency
stop switches, and the maintaining
of permissible ambient conditions.
BML displacement sensors may not
be used in life-saving systems, in
aircraft, etc.
1.4 Validity
This manual is applicable to
displacement sensors of type
BML-S1C0-...-KAxx.
An overview of the various
versions can be found in section 11
"Versions" (refer to part label).
Emission tests:
RF Emission
EN 55011 Group 1, Class A+B
Noise immunity tests:
Static electricity (ESD)
EN 61000-4-2 Severity level 3
Electromagnetic fields (RFI)
EN 61000-4-3 Severity level 3
Fast transients (Burst)
EN 61000-4-4 Severity level 3
Surge
EN 61000-4-5 Severity level 2
Line-induced noise induced by
high-frequency fields
EN 61000-4-6 Severity level 3
Magnetic fields
EN 61000-4-8 Severity level 4