Publicité
Les langues disponibles
Les langues disponibles
80 MHz to 800 MHz
d = 1.2 √P
800 MHz to 2,7 GHz
d = 2.3 √P
Where p is the maximum output power
rating of the transmitter in watts (W) accor-
ding to the transmitter manufacturer and
d is the recommended separation distance
Radiated RF
10V/m,
10V/m,
in metres (m). Field strengths from fixed RF
IEC 61000-4-3
80% Am at 1kHz
80% Am at 1kHz
transmitters, as determined by an electro-
magnetic site survey,
a
should be less than
the compliance level in each frequency
range.
b
Interference may occur in the vicinity of
equipment marked with the following
symbol:
NOTE 1: At 80 MHz and 800 MHz, the higher frequency range applies.
NOTE 2: These guidelines may not apply in all situations. Electromagnetic propagation is affected by absorption and
reflection from structures, objects and people.
a
Field strengths from fixed transmitters, such as base stations for radio (cellular / cordless) telephones and land mobile
radios, amateur radio, AM and FM radio broadcast and TV broadcast cannot be predicted theoretically with accuracy. To as-
sess the electromagnetic environment due to fixed RF transmitters, an electromagnetic site survey should be considered. If
the measured field strength in the location in which the device is used exceeds the applicable RF compliance level above,
the device should be observed to verify normal operation. If abnormal performance is observed, additional measures may
be necessary, such as re-orienting or relocating the device.
b
Over the frequency range 150 kHz to 80 MHz, field strengths should be less than 3 V/m.
Recommended separation distances between portable and mobile RF communications equipment and the device.
The EasyRAPID (
02022525000100) is intended for use in an electromagnetic environment in which radiated RF distur-
bances are controlled. The customer or the user of the EasyRAPID (
02022525000100) can help prevent electroma-
gnetic interference by maintaining a minimum distance between portable and mobile RF communications equipment
(transmittters) and the device as recommended below, according to the maximum output power of the communications
equipment.
Separation distance according to frequency of transmitter (m)
Rated maximum output
power of transmitter
150 kHz to 80 MHz
80MHz to 800MHz
800MHz to 2.7GHz
(W)
d=3.5 √P
d=1.2 √P
d=2.3 √P
0,01
0.12
0.12
0,1
0.38
0.38
1
1.2
1.2
10
3.8
3.8
100
12
12
For transmitters rated at a maximum output power not listed above, the recommended separation distance d in metres (m)
can be estimated using the equation applicable to the frequency of the transmitter, where P is the maximum output power
rating of the transmitter in watts (W) according to the transmitter manufacturer.
NOTE 1: At 80 MHz and 800 MHz, the separation distance for the higher frequency range applies.
NOTE 2: These guidelines may not apply in all situations. Electromagnetic propagation is affected by absorption and
reflection from structures, objects and people.
Guidance and manufacturer's declaration - electromagnetic immunity
The
is intended for use in the electromagnetic environment specified below. The
EasyRAPID (
02022525000100)
customer or the user of the
, should assure that it is used in such an environment.
EasyRAPID (
02022525000100)
Test frequency
Band
a
)
Service
)
Modulation
)
Modulation
) (W)
Distance (m)
a
b
b
(MHz)
(MHz)
Pulse
385
380 – 390
TETRA 400
modulation
b
)
1,8
0,3
18 Hz
FM c)
GMRS 460,
±5 kHz
450
430 – 470
2
0,3
FRS 460
deviation
1 kHz sine
710
Pulse
LTE Band
745
704 – 787
modulation
b
)
0,2
0,3
13, 17
217 Hz
780
Radiated RF
IEC61000-4-3
GSM
(Test
810
800/900,
specifications
Pulse
for
TETRA 800,
870
800 – 960
modulation
b
)
2
0,3
iDEN 820,
ENCLOSURE
18 Hz
CDMA 850,
PORT
930
IMMUNITY to
LTE Band 5
RF wireless
GSM 1800;
communica-
1 720
tions
CDMA 1900;
Pulse
1 700 –
GSM 1900;
equipment)
1 845
modulation
b
)
2
0,3
1 990
DECT;
217 Hz
LTE Band 1, 3,
1 970
4, 25; UMTS
Bluetooth,
WLAN,
Pulse
2 400 –
2 450
802.11 b/g/n,
modulation
)
2
0,3
b
2 570
RFID 2450,
217 Hz
LTE Band 7
5 240
Pulse
5 100 –
WLAN 802.11
5 500
modulation
b
)
0,2
0,3
5 800
a/n
217 Hz
5 785
NOTE: If necessary to achieve the IMMUNITY TEST LEVEL, the distance between the transmitting antenna and the
ME EQUIPMENT or ME SYSTEM may be reduced to 1 m. The 1 m test distance is permitted by IEC 61000-4-3.
a) For some services, only the uplink frequencies are included.
b) The carrier shall be modulated using a 50% duty cycle square wave signal.
c) As an alternative to FM modulation, 50% pulse modulation at 18 Hz may be used because while it does not
represent actual modulation, it would be worst case.
The MANUFACTURER should consider reducing the minimum separation distance, based on RISK MANAGEMENT,
and using higher IMMUNITY TEST LEVELS that are appropriate for the reduced minimum separation distance. Mi-
nimum separation distances for higher IMMUNITY TEST LEVELS shall be calculated using the following equation:
6
E =
√P
d
Where P is the maximum power in W, d is the minimum separation distance in m, and E is the IMMUNITY TEST
LEVEL in V/m.
Safety Information
The symbols below can be found in the Instruction Manual as well as on labels and other components.
"PLEASE REFER TO THE INSTRUCTIONS
FOR USE" symbol
Symbol for "COMPLIES WITH MDD
93/42/EEC as amended by directive
0068
2007/47/EC"
"MANUFACTURER" symbol
SN
Symbol for "SERIAL NUMBER"
Symbol for "DIRECT CURRENT"
Latex free
Protected against solid foreing objects
IP21
of 12.5mm Ø and greater and protected
against vertically falling water drops.
Appliance date of production: the second pair of digits in the lot number identifies the year, the third pair identifies the month.
(LOT 1016100001; 16 = 2016; 10 = October)
THE PRODUCT COMPLIES WITH:
EN 1060-1: 1995/A2: 2009 Non-invasive sphygmomanometers – Part 1 General requirements
EN 1060-3: 1997/A2:2009 Non-invasive sphygmomanometers – Part 3: Supplementary requirements for electro-mechanical
blood pressure measuring systems
EN 1060-4: 2004 Non-invasive sphygmomanometers – Part 4: Procedures to determine the overall system accuracy of
automated non-invasive sphygmomanometers
THIS PRODUCT COMPLIES WITH THE DIRECTIVE 2012/19/EU.
The crossed bin symbol on the appliance indicates that the product, at the end of its life, must be disposed of
separately from domestic waste, either by taking it to a separate waste disposal site for electric and electronic ap-
pliances or by returning it to your dealer when you buy another similar appliance. The user is responsible for taking
0.23
the appliance to a special waste disposal site at the end of its life. If the disused appliance is collected correctly as
separate waste, it can be recycled, treated and disposed of ecologically; this avoids a negative impact on both the
0.73
environment and health, and contributes towards the recycling of the product's materials. For further information regarding
the waste disposal services available, contact your local waste disposal agency or the shop where you bought the appliance.
2.3
7.3
THIS PRODUCT COMPLIES WITH EU DIRECTIVE 2006/66/EC
The crossed bin symbol on the batteries indicates that, at the end of their life, they must be disposed of separately
23
from domestic waste, either by taking them to a separate waste disposal site for batteries or by returning them to
your dealer when you buy similar rechargeable or non-rechargeable batteries. The chemical symbols Hg, Cd, Pb,
printed under the crossed bin symbol, indicate the type of substance contained in the batteries: Hg=Mercury, Cd=Cadmium,
Pb=Lead. The user is responsible for bringing batteries, at the end of their life, to the appropriate collection facilities in order to
facilitate treatment and recycling. The correct disposal of your old toy will help prevent potential negative consequences for
the environment and human health and favour the recycling of the materials of which the product is made. Illegal disposal of
the product by the user will damage the environment and human health. For further information regarding the waste disposal
services available, contact your local waste disposal agency or the shop where you bought the appliance.
Pouch cleaning symbols
Wash by hand in cold water,
Do not bleach,
30° C
IMMUNITY
TEST LEVEL
Do not tumble dry,
(V/m)
line drying,
Do not iron,
27
Do not dry clean.
28
9
28
28
28
9
"TYPE BF APPLIED PART" symbol
Storage and transport humidity
symbol
Storage and transport temperature
symbol
Caution
Lot number
Catalogue Number
Atmospheric pressure
0068
PIKDARE S.p.A.
Via Saldarini Catelli, 10
22070 - Casnate con Bernate (CO) - Italy
www.picsolution.com
Publicité
