EINHELL GE-LM 36/4in1 Li Instructions D'origine page 40

3. Fill the tank (Item 10a) with saw chain oil. In
the process, make sure that no dirt enters
the tank, as this could cause the oil nozzle to
become blocked.
4. Screw the oil tank lid (Item 10) back on again.
The pole-mounted pruner will be ready for use
after you have screwed it to the motor unit (see
section 5.2.6).
5.4 Assembly/adjustments of the hedge trim-
mer
5.4.1 Assembly
The hedge trimmer is ready for use once the
connecting tube has been converted (see section
5.3.1) and it has been screwed to the motor unit
(see section 5.2.6).
5.4 Adjusting the housing tilt (Fig. 23)
Press the lock-off button (Item 15a) and adjust
the tilt of the housing to any of 7 latching posi-
tions.
5.5 Fitting the battery (Fig. 24a-24b)
Push the battery into the battery mount provided
(Item 1). The battery will be heard to click into
place when it has been pushed fully in. To remove
the battery, press the pushlock button (Item N)
and pull out the battery.
Notice!
Never combine batteries with diff erent capacities
(Ah).
Use only batteries which are charged to the same
level. Never combine full and half-full batteries.
Always charge the two batteries simultaneously.
The equipment's operating time depends on the
battery with the lower charge level. The two batte-
ries must always be fully charged before use.
5.6 Charging the battery (Fig. 25)
1. Take the battery pack out of the tool. Do this
by pressing the pushlock button.
2. Check that your mains voltage is the same as
that marked on the rating plate of the battery
charger. Insert the power plug of the charger
into the socket outlet. The green LED will then
begin to fl ash.
3. Insert the battery into the charger.
4. In the section entitled „Charger indicator" you
will fi nd a table with an explanation of the LED
indicator on the charger.
Anl_GE_LM_36_4in1_Li_SPK9.indb 40 Anl_GE_LM_36_4in1_Li_SPK9.indb 40
GB
The battery can become a little warm during the
charging. This is normal.
If the battery pack fails to charge, check:
•
whether there is voltage at the socket outlet
•
whether there is good contact at the charging
contacts
If the battery pack still fails to charge, send
•
the charger
•
and the battery pack
to our customer service center.
To ensure that items are properly packaged
and delivered when you send them to us,
please contact our customer service or the
point of sale at which the equipment was
purchased.
When shipping or disposing of batteries and
cordless tools, always ensure that they are
packed individually in plastic bags to prevent
short circuits and fi res.
To ensure that the battery pack provides long ser-
vice, you should take care to recharge it promptly.
You must recharge the battery pack when you
notice that the performance of the device drops.
Never allow the battery pack to become fully di-
scharged. This will cause it to develop a defect.
5.7 Battery charge level indicator (Fig. 26)
Press the battery charge level indicator button
(Item M). The battery charge level indicator (Item
L) shows the charge status of the battery using 3
LEDs.
All 3 LEDs are lit:
The battery is fully charged.
2 or 1 LED (s) are lit:
The battery has an adequate remaining charge.
1 LED fl ashes:
The battery is empty, recharge the battery.
All LEDs blink:
The battery temperature is too low. Remove the
battery from the equipment, keep it at room tem-
perature for one day. If the fault reoccurs, this me-
ans that the rechargeable battery has undergone
exhaustive discharge and is defective. Remove
the battery from the equipment. Never use or
charge a defective battery.
- 40 -
21.04.2022 16:02:40 21.04.2022 16:02:40