Unpacking; Before Starting The Equipment - Scheppach PLM1800 Traduction Des Instructions D'origine

Noise & vibration
m Warning: Noise can have serious effects on
your health. If the machine noise exceeds 85 dB (A),
please wear suitable hearing protection.
Sound pressure level L 93,7 dB(A) (EN ISO 3744)
pA
Sound power level L 92 dB(A) (EN ISO 11201)
WA
Uncertainty K 2 dB(A)
wa/pA
Keep the noise emissions and vibrations to am
minimum!
• Only use appliances which are in perfect working
order.
• Service and clean the appliance regularly.
• Adapt your working style to suit the appliance.
• Do not overload the appliance.
• Have the appliance serviced whenever necessary.
• Switch the appliance off when it is not in use.

7. Unpacking

Open the packaging and remove the device carefully.
Remove the packaging material as well as the pack-
aging and transport bracing (if available).
Check that the delivery is complete.
Check the device and accessory parts for transport
damage. If possible, store the packaging until the
warranty period has expired.
Familiarise yourself with the device by means of the
operating manual before using for the first time.
With accessories as well as wearing parts and spare
parts use only original parts. Spare parts can be ob-
tained from your specialist dealer.
When ordering please provide our article number as
well as type and year of manufacture for your equip-
ment.
m ATTENTION! The device and packaging
materials are not toys! Children must not be
allowed to play with plastic bags, film and
small parts! There is a risk of swallowing and
suffocation!

8. Before starting the equipment

m ATTENTION! Always make sure the device is
fully assembled before start-up!
Before each use, check the following:
• Proper function of the on and off button, incl. the
emergency switch (if available).
Locked disconnected protective equipment
•
by gradual opening of every separating protective
equipment to be able to turn the machine off and
checking that the machine cannot be turned on
whenever the protective equipment is open
 www.scheppach.com /  service@scheppach.com /  +(49)-08223-4002-99 /  +(49)-08223-4002-58
Brake
•
Switch on the machine at the start of work and allow
the machine to reach speed. Now switch the ma-
chine off again. The engine must come to a standstill
within 10 seconds. Otherwise, there is a defect.
Anti-kick claws
•
at least once per shift by a visual inspection to estab-
lish that they are in good working order, for example,
that the contact surface has not been damaged by
impacts and that the anti-kick claws fall back without
hindrance due to their own weight;
Planing blades
•
for signs of damage and to ensure they are posi-
tioned correctly.
The machine may only be used if all these condi-
tions are satisfied.
• Use only well sharpened and maintained blades.
Use only blades that are designed for the machine.
• Use pusher wood or sticks which are in perfect
condition for machining short workpieces.
• Connect the machine to a dust and chip extractor.
• Check that the stop is secure before starting the
machining work.
• Ensure that you can maintain your balance at all
times. Stand to the side of the machine.
• Whilst the machine is running keep your hands at
a safe distance from the cutting block and from the
point at which the chips are discharged.
• Do not start the planing work until the cutting block
has reached the required speed.
• Also ensure that the workpiece does not contain
any cables, wires, cords or the like. Do not ma-
chine any wood which has lots of knots or knot
holes.
• Secure long workpieces to prevent them tipping
over at the end of the planing process. Use roller
stands, for example, or similar devices for this pur-
pose.
• Removing sawdust and chippings from the ma-
chine when running is strictly prohibited.
• Switch off the machine immediately it is jams. Pull
out the mains plug and remove the jammed work-
piece.
• Set the smallest cutting size after use to prevent
the risk of injury.
m CAUTION!
The machine must be secured to the floor / counter-
top using suitable screws / screw clamps since oth-
erwise there is a risk that it will tip over.
• Before you connect the equipment to the mains
supply make sure that the data on the rating plate
are identical to the mains data.
GB | 25