Beninca CP.J4 ESA Mode D'emploi page 17

By selecting this function, the receiver is waiting for (Push) a transmitter code to be erased from memory.
CLR If the code is valid, it will be stored in memory and OK will be displayed.
If the code is not valid, the Err message will be displayed.
RTR The memory of the receiver is entirely erased. Confirmation for the operation is asked.
The number of cycles (open+close) completed by the system is displayed.
When the push-button <PG> is pressed once, the first 4 digits are displayed, if the push-button is pressed once more,
the last 4 digits are displayed.
E.g. <PG> 0012 >>> <PG> 3456: 123.456 cycles were performed.
This function allows to activate the indication of maintenance required after a certain number of operations, preset by
the installer.
To activate and select the number of operations, proceed as follows:
Press the <PG> button, OFF is displayed, indicating that the function is disabled (default).
Select one of the numbers shown (from OFF to 100) by using the <+> and <-> keys . The figures express the value of
hundreds of cycles (e.g.: the number 50 means 5000 operations).
Press OK to activate the function. The PROG message is displayed.
The warning of maintenance required is indicated to the user through the flashing of the courtesy light LEDs during the
opening and closing phases.
RESET of the control unit. WARNING: Returns the control unit to the default values.
When the <PG> push-button is pressed once, the RES wording begins to flash, if the push-button<PG> is pressed
once more, the control unit is reset.
Note: neither the transmitter codes nor the position and stroked of the gate leaf will be erased from the receiver.
The self-calibration of the triggering thresholds of the anti-crash device (amperometric sensor), as well as the stroke
learning are performed. See paragraph SELF-LEARNING
It allows to type in an access protection code to the programming of the control unit.
A four-character alphanumeric code can be typed in by using the numbers from 0 to 9 and the letters A-B-C-D-E-F.
The default value is 0000 (four zeros) and shows the absence of a protection code.
While typing in the code, this operation can be cancelled at any moment by pressing keys + and – simultaneously. Once
the password is typed in, it is possible to act on the control unit by entering and exiting the programming mode for around
10 minutes in order to allow adjustments and tests on functions.
By replacing the 0000 code with any other code, the protection of the control unit is enabled, thus preventing the access
to any other menu. If a protection code is to be typed in, proceed as follows:
- select the Code menu and press OK.
- the code 0000 is shown, also in the case a protection code has been previously typed in.
- the value of the flashing character can be changed with keys + and -.
- press OK to confirm the flashing character, then confirm the following one.
- after typing in the 4 characters, a confirmation message "CONF" appears.
- after a few seconds, the code 0000 appears again
- the previously stored protection code must be reconfirmed in order to avoid any accidental typing in.
If the code corresponds to the previous one, a confirmation message "OK" appears.
The control unit automatically exits the programming phase. To gain access to the Menus again, the stored protection
code must be typed in.
imPoRTANT: TAKE NoTE of the protection code and KEEP iT iN A SAFE PLACE for future maintenance operations.
To remove the code from a protected control unit, enter the programming mode with the password and reset the
code to the 0000 default value.
iF YoU LooSE THE CodE, PLEASE CoNTACT THE AUTHoRiSEd SERViCE CENTER FoR THE ToTAL RESET oF
THE CoNTRoL UNiT.
After any LoGiC change or control panel reset, it is necessary to perform a self-learning procedure
NUmBER oF CYCLES (Nman)
mAiNTENANCE (maci)
RESET (RES)
AUToSET (AUTO)
PASSWoRd (CODE)
(menu Auto - See Stroke self learning)
ATTENTioN:
17