Technical Data; Rotary Hammer; Noise/Vibration Information; Safety Instructions - Milwaukee K 540 S Notice Originale

Technical DaTa

Technical DaTa
K 540 S
Rated input .................................................................................................. 1100 W ..................................................1100 W
Output ........................................................................................................... 550 W ....................................................550 W
No-load speed ............................................................................................... 540 min
Speed under load max. .................................................................................. 420 min
Rate of percussion under load max. ............................................................. 3100 min
Single impact strength Drilling / Chiselling ....................................................7 / 7 J .....................................................7 / 7 J
Drilling capacity in concrete .............................................................................. 40 mm (SDS-max) ..................................40 mm (SDS-max)
Tunnel bit in concrete, bricks and limestone..................................................... 65 mm (SDS-max) ..................................65 mm (SDS-max)
Core cutter in concrete, bricks and limestone ................................................. 105 mm (SDS-max) ................................105 mm (SDS-max)
Chuck neck diameter ........................................................................................ 66 mm ...................................................66 mm
Weight according EPTA-Procedure 01/2003 .................................................... 6,1 kg .....................................................6,1 kg

noise/Vibration information

Measured values determined according to EN 60 745.
Typically, the A-weighted noise levels of the tool are:
Sound pressure level (K=3 dB(A)) ................................................................. 93,0 dB (A) .............................................91,5 dB (A)
Sound power level (K=3 dB(A)) .................................................................. 104,0 dB (A) ...........................................102,5 dB (A)
Wear ear protectors!
Total vibration values (vector sum in the three axes) determined according to EN 60745.
Vibration emission value a
h
Hammer-drilling in concrete: ....................................................................... 16,8 m/s
Uncertainty K .................................................................................................. 1,5 m/s
Chiselling: ..................................................................................................... 16,7 m/s
Uncertainty K .................................................................................................. 1,5 m/s
WaRninG
The vibration emission level given in this information sheet has been measured in accordance with a standardised test given in
EN 60 745 and may be used to compare one tool with another. It may be used for a preliminary assessment of exposure.
The declared vibration emission level represents the main applications of the tool. However if the tool is used for different applications, with
different accessories or poorly maintained, the vibration emission may differ. This may significantly increase the exposure level over the total
working period.
An estimation of the level of exposure to vibration should also take into account the times when the tool is switched off or when it is running
but not actually doing the job. This may significantly reduce the exposure level over the total working period.
Identify additional safety measures to protect the operator from the effects of vibration such as: maintain the tool and the accessories, keep
the hands warm, organisation of work patterns.
WaRninG!
Read all safety warnings and all instructions, including
those given in the accompanying brochure. Failure to follow
the warnings and instructions may result in electric shock, fire and/
or serious injury. Save all warnings and instructions for future
reference.

SafeTy inSTRucTionS

Wear ear protectors. Exposure to noise can cause hearing loss.
use auxiliary handles supplied with the tool. Loss of control can
cause personal injury.
hold power tool by insulated gripping surfaces when
performing an operation where the cutting accessory may
contact hidden wiring or its own cord. Cutting accessory
contacting a „live" wire may make exposed metal parts of the power
tool „live" and could give the operator an electric shock.
Appliances used at many different locations including open air should
be connected via a residual current device (FI, RCD, PRCD) of 30mA
or les .
220 - 240 V
...............................................540 min
-1
...............................................420 min
-1
.............................................3100 min
-1
...............................................11,3 m/s
2
.................................................1,5 m/s
2
...............................................16,7 m/s
2
.................................................1,5 m/s
2
Always wear goggles when using the machine. It is recommended to
wear gloves, sturdy non slipping shoes and apron.
Sawdust and splinters must not be removed while the machine is
running.
Always disconnect the plug from the socket before carrying out any
work on the machine.
Only plug-in when machine is switched off.
Keep mains lead clear from working range of the machine. Always
lead the cable away behind you.
Do not use diamond core drills on hammer mode.
When working in walls ceiling, or floor, take care to avoid electric
cables and gas or waterpipes.
The dust produced when using this tool may be harmful to health. Do
not inhale the dust. Wear a suitable dust protection mask.

Rotary hammer

Rotary hammer
110 - 120 V
-1
-1
-1
GB
2
2
2
2
English
5