Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
Your Hot Tub is designed to provide optimum performance when
connected to the maximum electrical service. The listing below will show
the various options and performance levels available on your hot tub.
A new GFCI must be used for your Hot Tub installation. Do not use
an existing breaker (GFCI), as its condition is unknown.
Escape, Escape R
Sport, Crown II,
AMERICAS 60Hz
120v/240v
Circuit Breaker
20A/50A
Number of Wires
1.
Clean tub of all debris.
2.
Use a garden hose to fill your hot tub through the empty filter
canister (to avoid air pockets during filling) to the appropriate
level of a minimum 2 inches (5.08cm) over the filter skimmer.
3.
DO NOT USE WATER THROUGH A WATER SOFTNER.
4.
Locate the shut-off T-valves. Make sure they are in the up or
open position. (See page 8)
5.
Check heater and pump unions. Occasionally during
shipping these become loosened. A simple tightening of
these (if necessary) will do, being careful not to over tighten.
(See page 8)
6.
Once water has reached correct level, turn power on to the
hot tub.
7.
To activate jets and to purge air from the pump, press/push jet
button located on the top side control. A second press/push
Whirlpool Diverter Jet(s):
Your hot tub is equipped with at least one Whirlpool Diverter jet
(2, 3, or 4 position). These jets when turned will divert water to
different groups of jets. Each position is reached with a 90 degree
turn of the whirlpool jet face. Always turn the collar of the
diverter jet clockwise when possible. Remember, turning your
diverter will affect the flow of water to different seat jets. Adjust to
suit your personal needs.
Topside Control Pad:
Your hot tub is equipped with an electronic topside control pad. The
topside control pad wil allow you to control the speed of the pump,
the light, and the temperature setting, as well as some programming
options. Familiarize yourself with the topside control by viewing the
Quick Reference Card (QRC) supplied with your manual.
PERMASHELL
Western Red Cedar
As with any wood product, maintaining the "new" look requires a
consistent schedule of treating your cabinet with a quality CEDAR
sealing product.
5
POWER REQUIREMENTS
Escape Premium,
Bella,
CrownXL,
Impulse,
Rendezvous
Warrior XL
Impulse DP
Royal
120v
240v
15A
50A
3/4
3
4
START-UP INSTRUCTIONS
OPERATING INSTRUCTIONS
, FILTER, COVER & CABINET CARE MAINTENANCE
®
Sport, Crown II
Impulse, CrownXL Rendezvous Royal
EUROPE 50Hz
Circuit Breaker
Number of Wires
On all systems, your Hot Tub must be connected to a dedicated
circuit breaker that is not shared with any other equipment.
DO NOT USE EXTENSION CORDS OF ANY KIND.
will put the pump on high speed. Repeat this process until
water flows from the jets. When the jets are working, set the
pump to low speed. (See page 25)
8.
Some start-up chemicals will be needed; please see your
dealer for recommendations.
9.
Set the temperature located on the top side control (See page
24) to the desired setting. The heater will shut off when the
water temperature reaches the set temperature.
10. Place the hot tub cover on tub. Keeping the cover on the
hot tub when the tub is not in use will help minimize
operating costs.
11. The time it will take for the water temperature to reach the
desired setting will vary.
Air Control(s):
Your hot tub has at least one air control. This air control allows air
to mix with the water that streams out of your jets. Each air control
is responsible for a section of jets or a whirlpool diverter jet. The
air controls are marked "MIN" and "MAX" (minimum and
maximum) in order for the air control to have any effect the jet(s)
that it controls must be on and have water flow.
Deluxe L.E.D. Lighting System:
This L.E.D. Lighting System consists of individual light nodes that
are in coordination with the L.E.D. light housed in the light lens
within the vessel of the spa. The light varies in color and function
by pressing the light button. To turn on the system simply press the
light button once. To turn it off, repress the light button. To change
the color or light function just press the light button once, press it
one more time to shut it off and then after 3-5 seconds press it one
more time. To turn it off, press it once more.
Permawood
– Cape Cod Grey, Teak, Pecan
®
Maintenance for Permawood
®
strong household cleaners/solvents can cause damage/fading to the
surface of the cabinet. All cleaners should be tested on an out-of-the-
way section of cabinet before cleaning.
Escape,
Escape
Premium,
230v
230v
16A
32A
3
3
is to use mild soap and water. Some
Publicité
Table des Matières
