Technical Data; Unpacking; Attachment / Before Starting The Equipment - Scheppach PLC40 Traduction Des Instructions D'origine

• Always keep hands away from the work area when
the machine is running.
• Eye injuries due to glare,
• Touching hot parts of the device or workpiece (burn
injury),
• In case of improper protection risk of accident and
fire through sparks and slag particles,
• Harmful emissions from smoke and gases if there
is a lack of air or if closed rooms are insufficiently
extracted.
Warning! This electric tool generates an electro-
magnetic field during operation. This field can impair
active or passive medical implants under certain
conditions. In order to prevent the risk of serious or
deadly injuries, we recommend that persons with
medical implants consult with their physician and the
manufacturer of the medical implant prior to operat-
ing the electric tool.

6. Technical data

Mains connection
Output
On-load factor*
Working pressure
Insulation class
Cutting capacity
Stainless steel: 1 - 8 mm
Material
Dimensions L x W x H
Weight
Subject to technical changes!
Noise
m WARNING: Noise can have serious effects on
your health. If the machine noise exceeds 85 dB (A),
please wear suitable hearing protection.
On-load factor* = is the percentage of the operating
time, in which the machine can beused continuously
under normal temperature conditions. In relation to a
10-minute time period this means, for example, that
with a duty cycle of 20%, that it can be used for 2
minutes and then there should be a break of 8 min-
utes. If you exceed the duty cycle values then this will
trigger the overheating protection which will bring the
device to a stop until it has cooled down to the normal
working temperature. Exceeding the duty cycle val-
ues continuously can damage the device.
 www.scheppach.com /  service@scheppach.com /  +(49)-08223-4002-99 /  +(49)-08223-4002-58
230V ~ / 50Hz
15 - 40A
35% bei 40A (25°C)
20% bei 40A (40°C)
4 - 4,5 bar
H
0,1 mm - 12 mm
( depending on the
material)
Copper: 1 - 4 mm
Aluminum: 1 - 8 mm
Iron: 1 - 10 mm
Steel: 1 - 12 mm
375 x 169 x 250 mm
6 kg

7. Unpacking

Open the packaging and remove the device care-
fully. Remove the packaging material as well as the
packaging and transport bracing (if available). Check
that the delivery is complete. Check the device and
accessory parts for transport damage. In case of
complaints the dealer must be informed immediate-
ly. Subsequent complaints will not be accepted. If
possible, store the packaging until the warranty pe-
riod has expired. Read the operating manual to make
yourself familiar with the device prior to using it. On-
ly use original parts for accessories as well as for
wearing and spare parts. Spare parts are available
from your specialized dealer. Specify our part num-
bers as well as the type and year of construction of
the device in your orders.
m ATTENTION
The device and packaging materials are not toys!
Children must not be allowed to play with plas-
tic bags, film and small parts! There is a risk of
swallowing and suffocation!
8. Attachment / Before starting the
equipment
Connecting the cutting torch
• Insert the plasma burner plug (10a) into the plasma
burner connection socket (10) and tighten the union
nut hand-tight (see Fig. 1,3 + 4).
• Insert the plasma burner power plug (6) into the
plasma burner power socket (10) and tighten the
union nut hand-tight (see Fig. 1,3 + 4).
Connecting the ground cable
• Connect the ground terminal plug (9a) with the
ground terminal - connection socket (9). Make
sure that the connecting shaft is first connected
and then turned. The connecting shaft must face
upwards when plugging in the ground cable plug
(9a). After plugging in, the connecting shaft must
be rotated in a clockwise direction until it reaches
the stop, in order to lock it in place (see Fig. 1,3 +
5). This does not require force!
Connect the compressed air hose
• Connect the compressed air hose (19) on the
back of the plasma cutter to the compressed air
connection (19a). To do so, insert the side of the
compressed air hose into the compressed air con-
nection (19a) of the plasma cutter without a quick
connector (see Fig. 9).
• The pressure can be set via the knob (21) on the
condensate separator (see Fig. 9 - 12). Select a
pressure of 4–4.5 bar.
GB | 23