Bosch GRG 18V-16 C Professional Notice Originale page 10

10 | English
Battery model ProCORE18V...
LED
5 × continuous green light
4 × continuous green light
3 × continuous green light
2 × continuous green light
1 × continuous green light
1 × flashing green light
Operation
Suitable blind rivet/nosepiece combinations
The use of a combination not listed in the table below may
lead to poor fastening or a malfunction of the power tool.
Blind rivet
Size Rivet mandrel
Dia. 3.0 mm (1/8") Dia. 2.00−2.15 mm
Dia. 3.2 mm (1/8") Dia. 1.85−2.15 mm
Dia. 4.0 mm (5/32") Dia. 2.35−2.80 mm
Dia. 4.8 mm (3/16") Dia. 2.77−3.50 mm
Dia. 5.0 mm (3/16") Dia. 2.95−3.50 mm
Dia. 6.0 mm (1/4") Dia. 3.40−3.50 mm
Dia. 6.4 mm (1/4") Dia. 3.71−4.00 mm
Setting a blind rivet (see figures A1–A3)
– Prepare the workpieces to be connected. If no holes are
yet available, pre-drill the workpieces.
– Select a suitable nosepiece (1). Screw the nosepiece
onto the cover sleeve (2) and tighten it with the
wrench (9).
– Use the AUTO (18) button to select the required working
mode (see "Selecting the working mode", page 11).
– Insert the rivet mandrel of the blind rivet (20) into the
nosepiece (1).
– Hold the power tool tightly and push the blind rivet into
the pilot hole.
– Depending on the working mode, press the on/off switch
(12) and wait until the rivet mandrel has broken off.
– Tilt the power tool backwards so that the rivet mandrel
can fall into the mandrel container (5).
Note: After setting the blind rivet, ensure that the broken-off
rivet mandrel has fallen into the mandrel container before
setting the next blind rivet.
1 609 92A 6HD | (13.01.2022)
Recommendations for Optimal Handling of the
Battery
Protect the battery against moisture and water.
Only store the battery within a temperature range of −20 to
Capacity
50 °C. Do not leave the battery in your car in the summer, for
80–100 %
example.
60–80 % Occasionally clean the ventilation slots on the battery using a
soft brush that is clean and dry.
40–60 %
A significantly reduced operating time after charging indic-
20–40 %
ates that the battery has deteriorated and must be replaced.
5–20 %
Follow the instructions on correct disposal.
0–5 %
Nosepiece
Labelling
3.0/3.2
4.0
4.8/5.0
6.4
Changing the Nosepiece (see figure B)
The nosepiece magazine (4) contains nosepieces of three
different sizes, enabling the user to exchange nosepieces
quickly.
– Use the wrench (9) to unscrew the nosepiece (1) from
the cover sleeve (2).
– Screw the new nosepiece on and tighten it with the
wrench (9).
Empty the mandrel container (see figure C)
Always empty the mandrel container (5) for broken-off rivet
mandrels before it is completely full in order to prevent
blockages.
– Unscrew the mandrel container (5) by turning it anti-
clockwise.
– Empty the mandrel container (5) into a suitable recycling
or waste bin.
– Screw the mandrel container (5) back onto the power
tool by turning it clockwise.
Hole diameter
Dia. 2.3−2.4 mm
Dia. 2.7−2.8 mm
Dia. 3.3−3.4 mm
Dia. 4.6−4.7 mm
Bosch Power Tools